3M Workstation Monitor 724 Скачать руководство пользователя страница 19

Страница: 19 / 25

Procedure

Work Surface

a) Access the dual inline package (DIP) switches SW1 and SW2 through a slot

located at the bottom of the chassis. Adjust SW1 to the LOUD position and
SW2 to the ON position with a small screwdriver (Figure 4).

b) Plug in the AC adapter. Note that the red high work surface lamp (M) is

illuminated with an audible alarm (slow chirping beep).

c) Adjust DIP switch SW1 to the SOFT position. Note that the loudness of the

alarm decreases.

d) Adjust DIP switch SW2 to the OFF position. Note that the audible alarm is

silenced.

e) Attach the 3M

™

Monitor/Table Mat Cord 2380D and the 3M

™

Workstation

Monitor 724 ground wire to the RSB using the two wires with alligator
clips. Set the resistance as follows and observe Workstation Monitor 724
output:

3.1 Megohms – Red work surface lamp (M) OFF.

4.3 Megohms – Red work surface lamp (M) ON.

f) Disconnect the cords from the RSB.
g) Connect the ring terminal end of the Workstation Monitor 724 ground wire to

the metal snap of the Monitor/Table Mat Cord 2380D. The red work surface
lamp (M) should now be OFF.

Attach 3M

™

Workstation

Monitor 724 Ground

Cord or AC Adapter

Ground Wire

Workstation Monitor

724 Ground Cord

™

Monitor Table Mat Cord

™

Monitor Table Mat Cord

Conductive/

Dissipative

Work Surface #1

Conductive/

Dissipative

Work Surface #2

™

Workstation Monitor 724

Rear

AC Adapter

Ground Wire

™

Dual

Remote Splitter

™

Remote

Input Jack

Work Surface

Ground Cord

Ground

Figure 15 – 3M

™

Workstation Monitor 724 wire connection diagram for two work stations.

Содержание Workstation Monitor 724


























Результаты поиска

Содержание Workstation Monitor 724

Отзывы:

Похожие инструкции для Workstation Monitor 724

Бренды по названию

Популярные бренды

3M Workstation Monitor 724, Руководство пользователя

Результаты поиска

Содержание Workstation Monitor 724

Отзывы:

Похожие инструкции для Workstation Monitor 724

Бренды по названию

Популярные бренды