manualshive.com logo in svg

3M Scotch-Weld PG II LT, Руководство пользователя, Страница: 24 / 27

Поделиться
Скачать
3M Scotch-Weld PG II LT Скачать руководство пользователя страница 24

© 3M 2006

22

Flow Control

Flow control of adhesive with your new 3M™ Scotch-
Weld ™ Hot Melt Applicator PG II LT is easy. Any
operator familiar with the control devices should be
able to adjust the applicator for desired flow. To adjust
adhesive flow, a combination of these control methods
can be used.

The four control devices are:

1.  Speed of 3M Scotch-Weld Hot Melt Applicator PG

II LT movement.

2. The 

trigger.

3.  The applicator tip.

4. Air 

pressure.

The trigger of the applicator is uniquely designed to
allow for variable adhesive control. By pulling the
trigger slowly to the rear, you can observe the start of
adhesive flow. As you continue to pull the trigger
rearward, increasing amounts of adhesive are
dispensed.

Your 3M Scotch-Weld Hot Melt Applicator PG II LT is
equipped with a 9921 (.093’’) tip as a standard
equipment. This tip will provide maximum flow for all
3M™ Scotch-Weld™ Hot Melt LM Adhesives. The
brass extension tip (9946) will allow for maximum

control

of all the 3M Scotch-Weld Hot Melt LM

Adhesives and substantially reduce initial surge. This is
accomplished at a 

decrease

in flow rate. Speed of

movement is the preferred means to control flow. In the
event that this is inappropriate for your operation,
additional accessory tips are available.

Note

DO NOT REDUCE AIR PRESSURE BELOW 40
PSI.

If low adhesive flow occurs when operating at

reduced air pressure, return to maximum (80 psi) and
run at least one cartridge of adhesive through the
applicator and then return to the lower pressure. 

Tip No. 

Description

9913

2 Hole Spreader

9916

3 Hole Spreader

9917

3 Hole 1’’ Spreader

9921

.093’’ Fluted

9922

.063’’ Fluted

9726

“T” Tip P/G II

9940

.125’’ Fluted Tip

9946

.072’’ Brass Extension

9727

“L” Tip P/G II

3M Scotch-Weld Hot Melt
Applicator PG II LT Tips

9726 “T” tip for RSC carton closing and other uses.
9727 “L” tip for FOL carton closing and other uses.

9945 heavy-duty bench stand holds 3M Scotch-Weld
Hot Melt Applicator PG II LT in proper position
when the applicator is not is use.

9726 Tip

9727 Tip

9945 Stand

Содержание Scotch-Weld PG II LT




























Отзывы:

Нет отзывов