3M Scotch-Weld Hot Melt Applicator EC Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 33

background image

© 3M 2006

3

UNPACKING

Remove the applicator and temperature modules (attached to the applicator)
from their shipping container and inspect for obvious damage. If damaged,
do not use and immediately contact your 3M sales representative or your
authorized 3M distributor.

FEATURES

•

Industrial-grade, all-electric applicator, 120 VAC 40/60 Hz, 350 watts.

•

Designed for 3M™ Scotch-Weld™ Hot Melt Quadrack™ Adhesive Sticks.

•

Delivers up to 5.5 pounds of 3M adhesive per hour on demand.

•

Innovative transport mechanism minimizes dripping.

•

Applicator is supplied with five removable temperature modules.

Refer to Table 1 in the Temperature

Module Installation section for proper module selection for 3M Quadrack adhesive used.

•

Palm trigger helps improve operator comfort in high demand applications.

•

Stroke adjuster enables precise deposit of adhesive.

RoHS compliant means that the product or part does not contain any of the substances in excess of
the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission
Decision 2005/618/EC, unless the substance is in an application that is exempt under RoHS. Unless
otherwise stated by 3M in writing, this information represents 3M’s knowledge and belief based on
information provided by third party suppliers to 3M.

«
...
3
4
5
6
7
...
»

Содержание Scotch-Weld Hot Melt Applicator EC


































Отзывы:

Нет отзывов

Похожие инструкции для Scotch-Weld Hot Melt Applicator EC

Бренд: NailFire Страницы: 20

Бренд: DAJ Страницы: 12

Бренд: NEO TOOLS Страницы: 32

Бренд: Senco Страницы: 2

FramePro 600 Series

Бренд: Senco Страницы: 16

Бренд: U-Line Страницы: 27

Бренд: Simpson Страницы: 20

Бренд: tacwise Страницы: 5

Бренд: Parkside Страницы: 60

Бренд: Makita Страницы: 18

Бренд: Makita Страницы: 64

Бренд: Makita Страницы: 52

Бренд: Makita Страницы: 10

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 94

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды