1
3M™ PELTOR™ Headset
MT7H79* Series
HT*79* Series
TwinCup™ MT7*H540*
INTRODUCTION
Congratulations and thank you for choosing the 3M™ PEL-
TOR™ Headset for your hearing protection and communica-
tion needs. Welcome to the next generation of protective
communication!
SAFETY INFORMATION
Please read, understand, and follow all safety information in
these instructions prior to using the communication headset.
Retain these instructions for future reference.
WARNING:
• If the information and recommendations contained herein
are not adhered to, the protection afforded by the earmuffs
will be severely impaired.
• This hearing protector helps reduce exposure to hazardous
noise and other loud sounds.
Misuse or failure to wear
hearing protectors at all times that you are exposed to
hazardous noise may result in hearing loss or injury.
For proper use, see supervisor, user instructions, or contact
3M Technical Support.
• The output of the electrical audio circuit of this hearing
protector may exceed the daily limit sound level.
•
Specific models are designated as Intrinsically Safe. See
separate reference document for more information.
CAUTION:
•
Ensure the headset is fitted, adjusted and maintained in
accordance with these user instructions.
Improper fit of
this device will reduce its effectiveness in attenuating
noise. Consult the enclosed instructions for proper fit.
• Hearing protectors must be worn at all times in noisy sur-
roundings for proper protection.
• Although hearing protectors can be recommended for pro-
tection against the harmful effects of impulsive noise, the
Noise Reduction Rating (NRR) is based on the attenuation
of continuous noise and may not be an accurate indicator
of the protection attainable against impulsive noise such as
gunfire (wording required by EPA).
• The noise reduction may be lower when eyeglasses,
goggles or respirator straps are worn between the sealing
surface of the earmuff cushions and the sides of the
wearer’s head. For best noise reduction, select eyeglasses
or goggles that have thin, flat temples or straps which will
minimize interference with the seal of the earmuff cushions.
Pull long hair back to the extent possible and remove other
items that may degrade the earmuff seal such as pencils,
hats, jewelry or earbuds. Do not bend and reshape the
headband as this will cause a loose fit and allow sound
leakage.
• When worn according to the User Instructions, this hearing
protector helps reduce exposure to both continuous
noises, such as industrial noises and noises from vehicles
and aircraft, as well as very loud impulse noises, such as
gunfire. It is difficult to predict the required and/or actual
hearing protection obtained during exposure to impulse
noises. For gunfire, the weapon type, number of rounds
fired, proper selection, fit and use of hearing protection,
proper care of hearing protection, and other variables
will impact performance. If your hearing seems dulled or
you hear a ringing or buzzing during or after any noise
exposure (including gunfire), or for any other reason you
suspect a hearing problem, your hearing may be at risk. To
learn more about hearing protection for impulse noise, visit
www.3M.com/hearing.
NOTE:
• This earmuff is provided with electrical audio input. The
wearer should check correct operation before use. If distor-
tion or failure is detected, the wearer should refer to the
manufacturer’s advice.
• This product may be adversely affected by certain chemical
substances. Further information should be sought from the
manufacturer.
• Earmuffs, and in particular cushions, may deteriorate
with use and should be examined at frequent intervals for
cracking and leakage, for example.
•
The fitting of hygiene covers to the cushions may affect the
acoustic performance of the earmuffs.
• In Canada, users of hard hats combined with earmuffs
must refer to CSA Standard Z94.1 on industrial protective
headwear.
• Operating and storage temperature: -4°F (-20°C) to 131°F
(55°C).
• Weight of hearing protector:
o MT7H79A*, MT7H79B* and MT7H79F*: 381g
o MT7H79P3E: 320g
o HT*79A*, HT*79B* and HT*79F*: 381g
o HT*79P3E: 320g
o MT7*H540F*: 428g
o MT7*H540P3E: 345g
• 3M Svenska AB hereby declares that this 3M™ PELTOR™
Headset is in compliance with the essential requirements
and other provisions set out in the PPE Directive (89/686/
EEC) and other appropriate Directives. The product has
been tested and approved in accordance with EN 352-
1:2002, EN 352-3:2002 and EN 352-6:2002 as well as
other appropriate harmonic standards. Thereby they fulfil
the requirements for CE marking.
•
Specific models are also in conformance with the ATEX
Directive, see separate folder. A copy of the declaration
of conformity and additional information required in the
Directives can be obtained by contacting 3M in the country
of purchase. For contact information, see last pages of this
user instruction.
This product contains electrical and electronic com-
ponents and must not be disposed of using standard
refuse collection. Please consult local directives for
disposal of electrical and electronic equipment.
GB
Содержание PELTOR HT 79 Series
Страница 97: ...92 RU MT7N M40 1 HY100A 100 TKFL01 FP9007 HY79 MT7N 5 0112 2012 1 019 2011 3 19 SE 331 02 3 3 3 3 3M 3M...
Страница 114: ...109 3M 3M 3M GR...
Страница 117: ......