3M MG-1000 Скачать руководство пользователя страница 53

Страница: 53 / 90

SST Transport and Burster Mechanism Manual

75-0302-1450-8, Version 1

Ch. 4 Preventive Maintenance • 43

12. Open the cabinet of the device in which the Burster resides.

Warning! Disconnect power from the SST CPU Board. If you do not disconnect power, you

will damage the unit.

13. Disconnect the Burster from the SST Transport and remove the Burster.

14. Close the cabinet doors.

15. Conduct a visual inspection of the Burster for defects. Make sure that there are no loose,

frayed, or broken wires.

16. Use canned, dry air to blow out all ticket dust and dirt from the Burster. Make sure you

blow out the dust and dirt around the light sensors. For locations of the light sensors, refer

to Figure 4.7.

17. Clean the rollers using a clean soft cloth dampened with denatured alcohol.

Figure 4.7

Locations of Light Sensors

LS 0

LS 1

LS 2

LS 3

LS 4

Содержание MG-1000



























































































Результаты поиска

Содержание MG-1000

Отзывы:

Похожие инструкции для MG-1000

Бренды по названию

Популярные бренды

3M MG-1000, Руководство пользователя

Результаты поиска

Содержание MG-1000

Отзывы:

Похожие инструкции для MG-1000

Бренды по названию

Популярные бренды