3M MG-1000 Скачать руководство пользователя страница 51

Страница: 51 / 90

SST Transport and Burster Mechanism Manual

75-0302-1450-8, Version 1

Ch. 4 Preventive Maintenance • 41

Inspecting the SST Transport

After you clean the SST Transport, you should inspect the various parts to ensure that everything is

in working order. The following instructions describe the steps to inspect the SST Transport.

1. Check the side-to-side movement of the Magnetic Head.

Warning! Do not push down on the magnetic head or it will become misadjusted.

❑

Hold the Magnetic Head between your thumb and forefinger. The magnetic head

should swivel freely but when moved, it should not return to its original position

of its own accord. (Version 12 or older only.)

❑

Make sure the magnetic head is above the ticket channel.

Warning! Do not adjust the magnetic head. Once set at the factory, the adjustment should

not change. If it has been accidentally misadjusted, contact the factory for assis-

tance.

Checking Motor Speed

Note:

After June 2001 SST CPU boards no longer contain motor speed adjustment. Motor speed

is controlled by firmware (Versions 4.0.9 or higher).

Follow these instructions to check the motor speed:

1. Close the SST Transport if it is open.

Warning! Make sure that the gears are aligned properly before you shut the SST Trans-

port. Forcing it to shut when the gears are not aligned properly may bend the

teeth on the large nylon drive gear. Do not slam the SST Transport shut.

2. Carefully reinstall the unit in the device in which it resides. Turn power ON.

Note:

Do not overstress or pinch the cables. Also, ensure that all connections to the CPU Board

are proper.

3. Check the motor speed.

4. Note the current DIP switch settings.

5. Open all of the DIP switches on Switch Bank S1, located on the SST CPU Board.

6. Close DIP switch 7, and then close DIP switch 8.

Содержание MG-1000



























































































Результаты поиска

Содержание MG-1000

Отзывы:

Похожие инструкции для MG-1000

Бренды по названию

Популярные бренды

3M MG-1000, Руководство пользователя

Результаты поиска

Содержание MG-1000

Отзывы:

Похожие инструкции для MG-1000

Бренды по названию

Популярные бренды