3M AccuGlide HST 41000 Скачать руководство пользователя страница 12

Страница: 12 / 48

Important Safeguards

This safety alert symbol identifi es
important safety messages in this
manual. READ AND UNDERSTAND

THEM BEFORE INSTALLING OR
OPERATING THIS EQUIPMENT.

•

To reduce the risk associated with

mechanical

hazards:

−

Read, understand and follow all safety

and operating instructions before

operating or servicing the case sealer

−

Allow only properly trained and quali

personnel to operate and/or service this

equipment

•

To reduce the risk associated with

shear, pinch, and entanglement

hazards:

−

Turn air and electrical supplies off on

associated equipment before perform-

ing any adjustments, maintenance, or

servicing the taping heads

−

Never attempt to work on the taping

head or load tape while the box drive

system is running

•

To reduce the risk associated with sharp

blade hazards:

−

Keep hands and

ngers away from tape

cutoff blades under orange blade

guards. The blades are extremely sharp

Explanation of Signal Word Consequences

Indicates a potentially hazardous
situation, which, if not avoided,
may result in minor or moderate
injury and/or property damage.

CAUTION:

Indicates a potentially hazardous
situation, which, if not avoided,
could result in death or serious
injury and/or property damage.

WARNING:

WARNING

•

To reduce the risk associated with muscle

strain:

−

Use proper body mechanics when
removing or installing taping heads that are
moderately heavy or may be considered
awkward to lift

•

To reduce the risk associated with impact

hazards:

−

Place the taping head on a smooth level
surface when maintaining or servicing this
equipment

CAUTION

(Important Safeguards continued on next page)

HST 2" Taping Head - NA

February 2010

Содержание AccuGlide HST 41000

















































Результаты поиска

Содержание AccuGlide HST 41000

Отзывы:

Похожие инструкции для AccuGlide HST 41000

Бренды по названию

Популярные бренды

3M AccuGlide HST 41000, Инструкция и перечень запасных частей

Результаты поиска

Содержание AccuGlide HST 41000

Отзывы:

Похожие инструкции для AccuGlide HST 41000

Бренды по названию

Популярные бренды