background image

8

8.2 Replacing the Air Filter

3M recommends changing the filter every three months or when it begins to look 
dirty. Replacement filters are available from 3M (see Table 1). 
8.21  Hold down the filter release button on the side of the console.

8.22  Remove the hose and filter from the console by pulling the textured rubber 

plug where the hose emerges from the console. Rocking the plug back and 
forth can help loosen the filter. Do not pull the hose itself. Remove the 
filter from the hose fitting by depressing the metal release tab on the fitting 
and pulling the filter.

8.23  To install the new filter, follow the directions described previously under 

Sec. 6.0.

8.3 Replacing the Emitter Points

The emitter points, built into the plastic tip of the Ionized Air Gun 980, usually 
last the life of the unit. However, the tip should be replaced if it is broken, or if 
the points are bent, broken, otherwise damaged, or if you are unable to remove 
dirt by cleaning the points with isopropyl alcohol. A replacement tip containing 
a pair of emitter points is available from 3M (see Table 1).
8.31  Insert the tip of a screwdriver into the slot on the 3M

 Ionized Air Gun 980 

barrel. See Figure 4.

8.32  Using the screwdriver as a lever, loosen the old clip, grasp it between 

your thumb and forefinger, and detach it from the Ionized Air Gun 980. 
The emitter points are very sharp; touch only the plastic lip, and handle 
it carefully. To avoid damaging the points, do not touch them with hard 
objects such as a screwdriver.

8.33  To insert the new emitter points, hold the Ionized Air Gun 980 with the 

barrel pointing up.

8.34  Grasp the new clip between your thumb and forefinger, and align it so the 

curved edges match the curve of the inside of the Ionized Air Gun 980 
barrel.

Содержание 980















Отзывы: