3M 9332+ AURA, Быстрый старт

Страница: 9 / 9

Fitting Instructions
These fitting instructions must be followed each time a 3M
TM
Aura
TM
9300+ Series respirator is worn.
3b. Take both straps in your other hand. Hold the respirator
under your chin, with the nosepiece facing upwards and
pull the straps over your head.
Upper strap should
be positioned on the
crown of the head.
Strap should not be
twisted
Make sure the panels
are fully unfolded
Noseclip should be
moulded around nose
and cheeks to give a
good seal
Lower strap should
be positioned
below the ears.
Strap should not be
twisted
Respirator should be
correctly positioned on
your face and head
Disposable respirators are only effective when there is a good seal between the edges of the respirator and your face. If the seal is poor,
protection is compromised as contaminated air can leak in through any gaps.
3a. Cup the respirator in one hand with the open side towards
your face.
1. With the reverse side up and using the tab, separate the
top and bottom panels of the respirator to form a cup
shape. Bend slightly at the centre of the noseclip.
2. Ensure that both panels are fully unfolded.
6. Perform a fit-check by covering the front of the respirator
with both hands taking care not to disturb its fit.
If you’re using an unvalved respirator, exhale sharply.
If you’re using a valved respirator,
inhale
sharply.
If air leaks around the nose, readjust the noseclip to eliminate
leakage then repeat the fit check. If air leaks at the respirator
edges, work the straps back along the sides of the head to
eliminate leakage then repeat the fit check.
If you cannot
achieve a proper fit, DO NOT enter the hazardous area.
Consult your supervisor.
4.
Locate the upper strap across the crown of the head and
the lower strap below your ears. The straps must not be
twisted. Adjust the top and bottom panels for a comfortable
fit, ensuring that the panels and tab are not folded in.
5. Using both hands, mould the noseclip to the shape of the
nose to ensure a close fit and a good seal.
The respirator may not fit as well if you pinch the
noseclip using one hand. Use two hands.
+ +
1 2
+ + + +
3a 4 5 6
+
3b
+ +
1 2
+ + + +
3a 4 5 6
+
3b
+ +
1 2
+ + + +
3a 4 5 6
+
3b
+ +
1 2
+ + + +
3a 4 5 6
+
3b
+ +
1 2
+ + + +
3a 4 5 6
+
3b
+ +
1 2
+ + + +
3a 4 5 6
+
3b
Make sure that your face is clean shaven. Respirators should not
be worn with stubble, beards or other facial hair under the area
of the face seal as these can prevent a good seal to the face.
Make sure that long hair is tied back and jewellery is removed
so that it does not interfere with the seal to the face.
+ +
1 2
+ + + +
3a 4 5 6
+
3b
The Power to Protect Your World
SM
13898
Please recycle. Printed in UK.
© 3M 2011. All rights reserved
.
Scan this QR code with your smartphone
to be directed to further information on
3M
™
Aura
™
9300+ Disposable Respirators
For more information visit: www.3M.co.uk/Aura9300plus
3
Safety Solutions
3M United Kingdom plc
3M Centre
Cain Road
Bracknell
Berkshire RG12 8HT
Tel: 0870 60 800 60
Safety Solutions 3M
Ireland Limited
The Iveagh Building
The Park
Carrickmines
Dublin 18
Tel: 1 800 320 500
3M Safety Solutions – OH&ESD
3M
™
Aura
™
9300+ Disposable Respirators
Users of 3M Aura 9300+ should be fit tested. Call the 3M Safety Services Coordinator on 0845 601 3457
or visit the website for further information.
CH
AUR
AFP
3M