3M 7620-S-2 страница 6 Скачать руководство пользователя

Страница: 6 / 20

78-8117-0508-2 Rev D

4.0 Install Lug or Connector

4.1 Check to insure 3M

™

Cold Shrink QT–III Silicone Rubber Termination assembly fits over the selected lug or

connector. If lug or connector (

Figure 6

) will not fit through the termination core, clean the insulation (

per Step

5.0

) and slide termination on cable before installing lug or connector.

DO NOT REMOVE CORE AT THIS

TIME.

Clearance

Connector/Lug

Figure 6

NOTE: Refer to pages 18 – 20 for 3M Connector and Lug crimping information.
NOTE: For Aluminum Conductors - Thoroughly wire brush conductor strands to remove aluminum oxide layer.

Immediately insert conductor into lug or connector barrel as far as it will go.

4.2 Position connector or lug and crimp according to manufacturer's directions. Remove excess oxide inhibitor and

sharp crimp flashings following crimping.

5.0 Clean Cable Insulation and Lug or Connector Barrel Using Standard Practice

5.1 Wipe the cable insulation with one of the solvent saturated pads from the 3M

™

Cable Cleaning Preparation Kit

CC–2.

DO NOT ALLOW SOLVENT TO TOUCH SEMI-CON INSULATION SHIELD!

5.2 If abrasive must be used:

a. Use on insulation only.

DO NOT USE ABRASIVE ON SEMI-CON INSULATION SHIELD!

b. Use only aluminum oxide abrasive; grit 120 or finer, included in the 3M

™

Cable Cleaning Preparation Kit CC-2.

c. Be careful not to reduce the cable insulation diameter below that allowed by the kit.

6.0 Install Termination

Important Packaging Notice

In order to make sure that you receive an undamaged termination, this 3M™ Cold Shrink QT-III Termination is packed

with a RED SHIPPING CORE inside of the white core. Please remove the red shipping core BEFORE you install the ter-

mination. This shipping core can be recycled with other polypropylene waste.

6.1 Slide the termination body onto the cable and remove core. Pull while unwinding, counter-clockwise, starting

with the loose end (

Figure 7

). Make sure the termination body (not the core) is butted up to the edge of the

vinyl tape marker previously applied (

Figure 7

NOTE: Once the termination body makes contact over the mastic seal area, there is no need to continue

supporting the assembly. DO NOT PUSH OR PULL ON THE TERMINATION ASSEMBLY WHILE

UNWINDING THE CORE.

Vinyl Tape Marker

Counter-Clockwise

NOTE: The material being removed at this step is mixed polymers
and can be recycled with waste.

NOTE:

Figure 7

Содержание 7620-S-2





















Результаты поиска

Содержание 7620-S-2

Отзывы:

Похожие инструкции для 7620-S-2

Бренды по названию

Популярные бренды

3M 7620-S-2, Инструкция по эксплуатации

Результаты поиска

Содержание 7620-S-2

Отзывы:

Похожие инструкции для 7620-S-2

Бренды по названию

Популярные бренды