3DHS Extra 330SC Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 27

background image

www.modellmarkt24.ch

9

7. Apply a generous amount of epoxy to the bottom of the G-10 control horns and
base plate.

8. Reinsert the assembly into the elevator and wipe away any excess epoxy with a
cloth and denatured alcohol. Place a 3mm bolt through the horns to help insure
proper alignment and set aside to dry. Repeat for the other elevator half.

www.modellmarkt24.ch

«
...
7
8
9
10
11
...
»

Содержание Extra 330SC




























Отзывы:

Нет отзывов

Похожие инструкции для Extra 330SC

Бренд: Kadee Страницы: 2

SET OF FUNFAIR CARAVANS II

Бренд: Faller Страницы: 4

HALF-TIMBERED HOUSE

Бренд: Faller Страницы: 4

Бренд: Faller Страницы: 4

Бренд: GRAUPNER Страницы: 42

2 BEEKEEPER'S TRAILERS

Бренд: Faller Страницы: 8

Бренд: Fisher-Price Страницы: 4

Бренд: PARKZONE Страницы: 12

Starbeans Coffee Shop

Бренд: Great Little Trading Страницы: 6

Бренд: Lionel Страницы: 4

Three Rivers Fast Freight

Бренд: Lionel Страницы: 24

Big Bird Ride-On

Бренд: Playskool Страницы: 2

Fishbellied bridge

Бренд: Faller Страницы: 4

Бренд: Fisher-Price Страницы: 16

O-27 Santa Fe FT Passenger set

Бренд: Lionel Страницы: 16

BMW S1000RR RIDE-ON

Бренд: Jiajia Страницы: 16

Бренд: B.toys Страницы: 2

Little Singing Bear

Бренд: VTech Baby Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды