manualshive.com logo in svg

3DHISTECH PANNORAMIC SCAN RX 1.1, Руководство пользователя

Поделиться
Скачать
3DHISTECH PANNORAMIC SCAN RX 1.1 Скачать руководство пользователя страница 157

PANNORAMIC® SCAN RX 1.1 

TROUBLESHOOTING AND MAINTENANCE 

 

NOVEMBER 18, 2021 

156

 

FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES.

 

1.

 

Turn off the fluorescent illumination unit.

 

 Warning! 

Crush hazard! Stop the running digitization process and turn off the scanner (refer to 
chapter 

2.7 Power the Scanner On/Off

) before you proceed with filter module installation or 

removal. 

 

2.

 

Select the desired filter in the corresponding software window (see chapter 

6.1 Settings

). 

The filter will be positioned in such a way that the user can access it without having to 
turn the filter wheel manually.

 

3.

 

Power off the scanner. See chapter 

2.7 Power the Scanner On/Off

 on how to power off the 

device.

 

4.

 

Remove the protective cover of the device (see chapter 

9.5.1 Removing the Protective 

Covers

).

 

5.

 

Hold the filter module 

(3)

 by its handling pads (one on the right, one on the left (lateral) 

side of the module) and insert it in forward tilted position from above into the upper 
spring-loaded clamps 

(1)

 at the filter wheel.

 

 Warning! 

Avoid touching the surface of the filters and store the modules in their own boxes when not 
used. 

 

6.

 

Press the filter module down, until it safely connects to the bottom spring-loaded clamps 

(2)

 of the filter wheel. Mounting position of the filters: excitation filter 

(5)

; emission filter 

(4)

.

 

7.

 

To remove the filter module, first slightly tilt it out of its upper spring-loaded fixtures, then 
pull it out of the bottom spring-loaded components 

(1)

 and take it off.

 

8.

 

Place the protective cover back again (see chapter 

9.5.1 Removing the Protective Covers

).

 

9.

 

Power on the scanner. See chapter 

2.7 Power the Scanner On/Off

 on how to power on the 

device.

 

10.

 

Enter the respective parameters in the input fields e (see chapter 

6.1 Settings

).

 

11.

 

Turn the fluorescent illumination unit on again (consider the cooling time possibly 
required).

 

 

 

Содержание PANNORAMIC SCAN RX 1.1






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды