3D Systems VIDAR AdvantagePRO Series Скачать руководство пользователя

Страница: 30 / 50

19196-001 Rev. D

VIDAR Advantage Series User’s Guide

Top LED: feeder status

LED state

Digitizer condition Corrective action

Solid green

Ready

None. The feeder is ready to operate.

Off

ERROR: no feeder
attached

1. Turn off digitizer.
2. Remove feeder.
3. Inspect electrical connector and screws on

bottom of feeder.

Fast flashing green

ERROR: unknown
feeder attached

Check feeder:
1. Turn off digitizer.
2. Remove feeder.
3. Inspect electrical connector and screws on

bottom of feeder.

Slow flashing green

BUSY: film is
staging

None. This is normal operation.

Fast flashing green

ERROR: film
staging problem

Eject film by clicking the eject button in the
scanning application.

Center LED: Digitizer Status

LED state

Digitizer condition Corrective action

Solid green

Ready

None. The digitizer is ready to accept commands
from the scanning application.

Slow flashing green

BUSY: normalizing

None. This is normal operation. The LED will

flash slowly during initial calibration after power is
applied, and when the scanning application
initiates a calibration.

Slow flashing green

BUSY: tracking
(ADC)

None. This is normal operation. The LED will

flash periodically when the digitizer is idle.
Automatic Digitizer Calibration (ADC) is
independent of the scanning application.

Slow flashing green

BUSY: staging film

None. This is normal operation. The LED will
flash slowly while the digitizer is staging the film.

Slow flashing green

BUSY: Positioning
film

None. This is normal operation. The LED will
flash slowly while the scanning application is
positioning the film.

Slow flashing green

BUSY: digitizing film None. This is normal operation. The LED will

flash slowly while a film is being digitized.

Slow flashing green

BUSY: ejecting film None. This is normal operation. The LED will

flash slowly while the scanning application is
ejecting the film.

Off

ERROR

1. Make certain power is supplied to the digitizer,

and that the digitizer power switch is on.

2. If problem persists, get qualified technical help

(see “In case of difficulty,” later in this chapter).

Содержание VIDAR AdvantagePRO Series



















































Результаты поиска

Содержание VIDAR AdvantagePRO Series

Отзывы:

Похожие инструкции для VIDAR AdvantagePRO Series

Бренды по названию

Популярные бренды

3D Systems VIDAR AdvantagePRO Series, Руководство пользователя

Результаты поиска

Содержание VIDAR AdvantagePRO Series

Отзывы:

Похожие инструкции для VIDAR AdvantagePRO Series

Бренды по названию

Популярные бренды