3D Systems ProX DMP320 Скачать руководство пользователя

Страница: 26 / 83

3D SYSTEMS, INC

Deposition System

A soft coater moves the powder from the feeds onto the build platform .

Build Chute (with build platform)

The parts are printed on a printing plate which is bolted to the build platform . During the print process, the build platform

indexes down to allow subsequent layers of the part to be printed .

Feed Chute (with feed platform)

The feed chute (with feed platform) contains the new metal power . The platform lifts the powder to the correct height to supply

the coater with the right amount of metal powder .

Electrical Connector

Carries all power and signal connections from the process chamber to the build module .

Overflow Container

Holds the excess powder until it can be extracted and sieved for re-use .

Overflow Chute

Powder deposited in here is lead to the overflow containers.

Содержание ProX DMP320



















































































Результаты поиска

Содержание ProX DMP320

Отзывы:

Похожие инструкции для ProX DMP320

Бренды по названию

Популярные бренды

3D Systems ProX DMP320, Руководство пользователя

Результаты поиска

Содержание ProX DMP320

Отзывы:

Похожие инструкции для ProX DMP320

Бренды по названию

Популярные бренды