background image

2

TABLE OF CONTENT

INTRODUCTION .............................................................................................................................................................................. 3
ABOUT THIS GUIDE ........................................................................................................................................................................3
COPYRIGHT .................................................................................................................................................................................... 4
IMPORTANT SAFETY INFORMATION ............................................................................................................................................5
SPECIFICATIONS and REQUIREMENTS .......................................................................................................................................6
FAMILIARIZATION ...........................................................................................................................................................................7
FACILITY REQUIREMENTS .............................................................................................................................................................8
PREPARATION FOR WALL-MOUNT ............................................................................................................................................8-9
WALL-MOUNT INSTALLATION .....................................................................................................................................................10
TABLE-MOUNT INSTALLATION .................................................................................................................................................... 11
OPERATION ..............................................................................................................................................................................12-15
MAINTENANCE ..............................................................................................................................................................................16
SERVICE and SUPPORT ...............................................................................................................................................................17
SPARE PARTS ..........................................................................................................................................................................18-20

Содержание ProJet Cart Station






















Отзывы: