background image

3D Systems, Inc.

9

SETTING UP GEOMAGIC CAPTURE SERIES 3D SCANNER

Follow these steps to set up the Geomagic Capture Series 3D scanner in your Geomagic application.

Network Configuration

1. 

Make sure that all cables and cordsets that were delivered with a scanner are connected to the Geomagic Capture Series 3D 

scanner.

2. 

Connect the Geomagic Capture Series 3D scanner to a PC using a CAT5e Ethernet cable.

3. 

Enter the scanning command in the Geomagic application to connect the scanner.

Note: Consult the Online Help for additional information on the scanning command in the host application.
Note: If you receive the following warning message, check if all cables and 

cordsets are connected to the scanner and the PC, and then click 

OK 

to 

reconnect the scanner.

4. 

The Geomagic Capture application will initiate. Select the check box next to the name of detected scanner to connect the scanner 

to the application.

Note: If it is the first time to connect the Geomagic Capture series scanners to the PC, you must configure the network. 

Once the check box is selected, the application will automatically try to connect the scanner.
For more information, see the following 

Scanner Setup

 section.

Scanner Setup

Option 1: Automatic Configuration

1.  Go to Settings by clicking 

Settings

to check device status.

2.  In the Device Status, select the check box next to the name of detected scanner to 

connect the scanner to the application.

The application will try to automatically configure the network.

3.  Go to the Advanced Options by clicking 

Advanced Options

to check the network configurations.

4.  In the Device Status, check the connection status of the selected scanner if it says 

OK

.

Note: If there is a network conflict issue with the scanner, in the Network 

Configuration section, click 

Auto Configure

 to reconfigure the network.

Option 2: Manual Configuration

If there is an issue with network connection or you need to set a static IP address for your scanner, you must use the manual 

configuration. 

1.  In the Device Status, select the desired scanner.
2. 

In the Network Configuration, clear the 

Use DHCP

 check box located just above 

the Apply button.

3.  Enter values for the IP address, subnet mask, and default gateway.
4.  Click 

Apply

 to apply all changes.

Note: If you use a network hub to connect multiple devices at a common 

connection point in a network, the IP address of the network adapter in your 

PC should be the same as a default gateway of the device and the subnet 

mask of the network adapter should be the same as the subnet mask of the 

device. For example, if the IP address and subnet mask of your PC’s network 

adapter is 

192.168.61.1

 and 

255.255.255.0

, the default gateway and subnet mask address of the device should be the 

same as in your PC, 

192.168.61.1 

and 

255.255.255.0

.

However, if you use a router for your network connection, the default gateway and subnet mask of all connected 

devices including your PC should follow the IP address and subnet mask of your router.

The IP address of a PC’s network adapter can be checked in the properties of your local network.

To access the TCP/IPv4 properties in Windows™, perform the following steps:
a)  On the Windows Start menu, click 

Control Panel

.

b) Under 

Network and Internet

, click 

View 

network status and tasks

.

c)  In the left pane, click 

Change adapter 

settings

.

d) Right-click 

Local Area Connection

, then click 

Properties

.

Содержание Geomagic Capture


























Отзывы: