3D AEROWORKS VOUGHT F4U-1D CORSAIR Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 24

background image

RANGE OF TRAVEL:

NORMAL FLIGHT:

Elevator

+/- 5mm

Rudder

+/- 6mm

Aileron

+/- 5mm

AEROBATIC:

Elevator

+/- 8mm

Rudder

+/- 15mm

Aileron

+/- 10mm

LAUNCHING:

It was found that the safest and most successful launch technique for this model was the
under-arm style. The aircraft should be launched at approximately 20deg nose up at 50% to
75% power. Too steep and the aircraft will stall, too shallow and it will contact the ground.

«
...
19
20
21
22
23
...
»

Содержание VOUGHT F4U-1D CORSAIR

























Отзывы:

Нет отзывов

Похожие инструкции для VOUGHT F4U-1D CORSAIR

Бренд: MAC PARA Страницы: 12

Бренд: Just Flight Страницы: 96

Бренд: North Страницы: 24

Бренд: Beechcraft Страницы: 668

Бренд: Hobbico Страницы: 40

Бренд: Dancing Wings Hobby Страницы: 8

Бренд: Ozone Страницы: 23

Бренд: Hobbico Страницы: 20

REICHARD MODELSPORT CIRRUS F5J

Бренд: Hobby Club Страницы: 13

Бренд: Gradient Страницы: 16

Бренд: Gradient Страницы: 14

Бренд: Gradient Страницы: 16

Бренд: Gradient Страницы: 12

Бренд: Gradient Страницы: 15

Бренд: Gradient Страницы: 16

Бренд: BEST Kiteboarding Страницы: 14

Бренд: APCO Aviation Страницы: 24

Бренд: APCO Aviation Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды