background image

Balsawood Scale Airplane

● 

This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends 

on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be 

accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A 

TOY.

● 

Do not fly around some restricted location like airports, military bases, residential areas, etc.

● 

You will need to range check the transmitter to be sure you are not experiencing any interference.

● 

Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.

● 

If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from 

advanced expert fliers.

● 

Keep relevant items out of reach of children.

● 

This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform 

any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body 

strength.

● 

This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the 

goggles or dust-proof clothes when needed.

● 

Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the 

glue you need at your local stationery store.

SAFETY PRECAUTIONS

● 

Check/adjust servo centering, in order to adjust the control surface better.

● 

Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.

● 

Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail 

to ensure the best flight performance.

● 

Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink 

covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.

● 

Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage 

or damage to battery.

● 

The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those 

transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage. 

Check your device for details to see if it meets the features you need.

● 

When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum 

stroke of the throttle. Please set it yourself.

PRE-FLIGHT CHECKS

http://www.dwhobby.com/

SCG40

Tools Needed 

Specification

Suggested Equipment

ARF

Wingspan:2.33M (92inch) 
Fuselage Length:1.7M (67inch)

Flying weight:≈8.0kg (About 280pound)

Engine:RCGF 35cc   

Prop:20inch
Servo:37g*8pcs 

Содержание Savage Bobber









Отзывы: