3D AEROWORKS VOUGHT F4U-1D CORSAIR Скачать руководство пользователя | Manualshive

Страница: 20 / 24

background image

Installing the propeller:

-

Install the blade to the hub and secure it with an m2 x 10mm screw. (screw direction
towards the back of the hub)

-

Install the hub to the motor.

-

Secure with either metal nut provided or printed nut.

-

Install the spinner. The spinner is designed with an m5 thread to suit most small
motors with a regular cw thread.

-

Once balanced appropriately, glue Fuse 1in place with ca.

Fit the battery using Velcro as required and balance the aircraft inverted on the CG marking
points located

35mm aft of the leading edge at the wing root.

Using components

mentioned in the parts list, 30g of lead was needed in the nose section to balance without the
wheels.

«
...
18
19
20
21
22
...
»

Содержание VOUGHT F4U-1D CORSAIR

























Отзывы:

Нет отзывов

Похожие инструкции для VOUGHT F4U-1D CORSAIR

Бренд: Ozone Страницы: 30

Бренд: DUC Hélices Страницы: 24

Бренд: Wowings Страницы: 17

Бренд: Yak Страницы: 82

Бренд: Beechcraft Страницы: 51

Mystique 2.9m ARF

Бренд: E-FLITE Страницы: 5

Бренд: MAC PARA Страницы: 40

Бренд: Diamond Страницы: 300

PILATUS PC12 M19

Бренд: Safran Страницы: 49

HC-D2MV20-3 Series

Бренд: Hartzell Страницы: 204

ATOM Legend S T1,5

Бренд: Zodiac Aerospace Страницы: 83

Бренд: Aeropilot Страницы: 40

Бренд: Aeropro Страницы: 50

Бренд: WOODCOMP Страницы: 17

Бренд: Pipistrel Страницы: 5

Бренд: Pipistrel Страницы: 17

Бренд: Pipistrel Страницы: 98

1001 AT 912 LSA

Бренд: Pipistrel Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды