3Com LSBM1SRP1M1 страница 110 Скачать руководство пользователя

Страница: 110 / 128

Installation Manual
H3C S9500 Series Routing Switches

Appendix B Engineering Labels for Cables

B-1

Appendix B Engineering Labels for Cables

Engineering labels are affixed to both ends of the various cables to identify the physical

positions of cables on different devices. Labels on the cables facilitate correct and

orderly connection of cables, and easy maintenance after the installation.

There are two types of engineering labels, specialized for the power cables and signal

cables respectively. The power cables include the AC power cables and DC power

cables (excluding the power cable that connects the distribution box and the cabinet).

The signal cables include external cables of alarm box, Ethernet cables, optical fibers,

trunk cables and subscriber cables (excluding the antenna feeders).

Note:

In case there is special requirement from the user of the equipment on the description

method of the labels, the labels should be printed accordingly. However, this must be

stated in the self-check report.

B.1 Introduction to Labels

B.1.1 Material

Material: Polyester (PET), with UL and CSA certifications

Color: chalk white

Thickness: 0.09mm

Ambient temperature: -29~149 degrees Celsius

Laser printing or handwriting with oiliness markers

B.1.2 Type and Shape

There are two types of engineering labels for power cables and signal cables

respectively.

I. Label for signal cables

The label for signal cables is L-shaped with fixed dimensions, as shown in Figure B-1

(expressed in mm).

Содержание LSBM1SRP1M1

































































































































Результаты поиска

Содержание LSBM1SRP1M1

Отзывы:

Похожие инструкции для LSBM1SRP1M1

Бренды по названию

Популярные бренды

3Com LSBM1SRP1M1, Руководство по установке

Результаты поиска

Содержание LSBM1SRP1M1

Отзывы:

Похожие инструкции для LSBM1SRP1M1

Бренды по названию

Популярные бренды