manualshive.com logo in svg

3Com iRadar S120R, Руководство по началу работы

Поделиться
Скачать
3Com iRadar S120R Скачать руководство пользователя страница 22

2-2

C

HAPTER

 2: I

NSTALLING

 

THE

 S

YSTEM

Installing the System on a Table Top or in a 
Free-Standing Stack

To install the Switch 3900 system on a table top or in 
a free-standing stack, follow these instructions:

1

See Appendix B for site requirements.

2

Turn the system on its side.

3

Remove the protective covering from the rubber feet.

4

Place one rubber foot in each marked area at the four 
corners of the unit.

5

Turn the system onto its feet.

6

Verify that the air intake vents and fan exhaust vents 
at the sides of the system are not blocked.

To install the system into a free-standing stack, place 
the system on top of another. Be sure that the rubber 
feet of the upper unit fit securely in the recesses in 
the top of the lower unit. See Figure 2-1.

CAUTION: 

Stack no more than eight SuperStack II 

systems in a single free-standing stack.

You are now ready to cable your system. For 
instructions, see Chapter 3.

Figure 2-1   

Stacking the Switch 3900

Status

1x

6x

12x

7x

13x

18x

24x

19x

25x

30x

36x

31x

green

= enabled, link OK

flashing green

= disabled, link OK

off

= link fail

Fault

Power

10/100 BASE - TX

2

3

1

10 11 12

4

5

6

7

8

9

2

3

1

10 11 12

4

5

6

7

8

9

14 15 16 17

13

18 19 20 21

22 23 24

14 15 16 17

13

18 19 20 21

22 23 24

26 27 28 29

25

30 31 32 33

34 35 36

26 27 28 29

25

30 31 32 33

34 35 36

Pckt

Stat

Pckt

Stat

Pckt

Stat

Status

1x

6x

12x

7x

13x

18x

24x

19x

25x

30x

36x

31x

green

= enabled, link OK

flashing green

= disabled, link OK

off

= link fail

Fault

Power

10/100 BASE - TX

2

3

1

10 11 12

4

5

6

7

8

9

2

3

1

10 11 12

4

5

6

7

8

9

14 15 16 17

13

18 19 20 21

22 23 24

14 15 16 17

13

18 19 20 21

22 23 24

26 27 28 29

25

30 31 32 33

34 35 36

26 27 28 29

25

30 31 32 33

34 35 36

Pckt

Stat

Pckt

Stat

Pckt

Stat

Place the feet of one system into the
mounting recesses of the system below it.

Super Stack II 

Switch 3900

Super Stack II 

Switch 3900

Status

1x

6x

12x

7x

13x

18x

24x

19x

25x

30x

36x

31x

green

= enabled, link OK

flashing green

= disabled, link OK

off

= link fail

Fault

Power

10/100 BASE - TX

2

3

1

10 11 12

4

5

6

7

8

9

2

3

1

10 11 12

4

5

6

7

8

9

14 15 16 17

13

18 19 20 21

22 23 24

14 15 16 17

13

18 19 20 21

22 23 24

26 27 28 29

25

30 31 32 33

34 35 36

26 27 28 29

25

30 31 32 33

34 35 36

Pckt

Stat

Pckt

Stat

Pckt

Stat

Super Stack II 

Switch 3900

Содержание iRadar S120R



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды