3Brain BioCAM X Скачать руководство пользователя страница 12

Страница: 12 / 45

Power button

Camera Link

USB

BCExt connector

Power port

•

Camera-link

: SDR mini Camera Link connector to connect the BioCAM X to the acquisition board

mounted in the host PC. Electrophysiological data and control signals are managed through this
interface.

•

USB

: this port is used only for firmware updates of the BioCAM X. For normal use it is not needed to

connect this interface.

•

BCExt connector: plug the BCExtAdapter cable to access extended functionalities such us triggering
and stimulation.

•

Power port: plug for the power supply unit.

BioChip slot

Bay Barrier & BioChip connector

Reference connector

LED1

LED2

•

BioChip slot: the slot through which the BioChip (contact pads side) is inserted into the BioCAM X for
electrical interfacing.

•

Bay Barrier & BioChip connector: immediately behind the BioChip slot, a protective movable Bay Bar-

rier blocks accidental overflows of liquids that might get in touch and damage the internal electronics.

Behind the Bay Barrier, the BioChip connector allows to connect the BioChip’s contact pads to the
internal circuitry. Electrical contacts are established only once the locking system is activated.

•

Reference connector: connector for the pseudo-reference electrode that need to be placed in the
bath solution of the BioChip cartridges.

•

LED1: a solid blue LED indicates whether the BioCAM X is powered (LED ON) or not (LED OFF). A sol-

id violet LED indicates a failure in BioCAM firmware. In addition, the LED1 blinks violet to indicate that

the temperature control is ON.

•

LED2

: a solid green LED indicates whether the BioCAM X is acquiring signal (LED ON) or is in stand-by

mode (LED OFF).

•

Power button

: push-button to power ON or OFF off the BioCAM X (the instrument need to be con

nected to a power line using the provided adaptor).

Содержание BioCAM X














































Результаты поиска

Содержание BioCAM X

Отзывы:

Бренды по названию

Популярные бренды

3Brain BioCAM X, Руководство пользователя

Результаты поиска

Содержание BioCAM X

Отзывы:

Бренды по названию

Популярные бренды