5
•
A small window will open so that you can
search for the driver software. Click "
Find
driver software on this computer"
in the
window.
•
Click "
Select from a list of device drivers on
this computer"
.
•
Click the "
Medium…"
button.
•
Click the "
Browse…"
button and select the
path for the driver.
•
Click “Yes” to confirm that the file should
be overwritten.
7.2 Software installation
Note on installing the software
For this software, please refer to the installa-
tion instructions available in the 3B NET
lab
™
software manual.
8. Operating without a computer
Operating a 3B NET
log
™ device without a
computer is achieved by using the buttons on
the operating panel. The functions of these
buttons may change according to the operation
being undertaken.
Note:
a menu selection can be can-
celled at any time by using the
Channel
←
button.
8.1 Battery level and temperature display
•
Switch on the 3B NET
log
™ device by
pressing the
On/Off
button.
•
Press the
Date/Time
↵
button.
The following should appear on the display:
e.g.:
BATTERY: 100%
TEMP.: 22.0°C
8.2 Setting the time
•
Switch on the 3B NET
log
™ device by
pressing the
On/Off
button.
•
Press the
Date/Time
↵
button twice (the
time field will appear on the display).
•
Press the
Store
↓
button (the input field for
SET TIME will appear on the display).
•
Specify the desired time in the input field
by pressing the
Rate
↑
or the
Store
↓
but-
ton and use the
Channel
←
button to skip
between the hours, minutes and seconds
fields.
•
Confirm by pressing the
Date/Time
↵
but-
ton.
8.3 Setting the date
•
Switch on the 3B NET
log
™ device by
pressing the
On/Off
button.
•
Press the
Date/Time
↵
three times (the
date field will appear on the display).
•
Press the
Store
↓
button (the input field for
SET DATE will appear on the display).
•
Specify the desired date in the input field
by pressing the
Rate
↑
or
Store
↓
button
and use the
Channel
←
button to skip be-
tween the year, month and day fields.
•
Confirm by pressing the
Date/Time
↵
but-
ton.
8.4 Application as a handheld device for
measuring current and voltage
•
Set up the 3B NET
log
™ equipment.
•
Connect the voltage/current input of chan-
nel A or B, as desired.
•
If necessary, disconnect any sensor which
might be connected to the same channel.
Setting and selecting measurement parame-
ters:
•
Press the
Channel
←
button (the menu
DISPLAY SIGNAL 1 will appear on the
display).
•
Select the desired measurement parame-
ter with the
Rate
↑
or
Store
↓
button.
•
Select the mode of operation with the
Date/Time
↵
button (the menu RANGE
SIGNAL 1 will appear on the display).
•
Select the desired mode of operation with
the
Rate
↑
or
Store
↓
button.
•
Confirm this selection with the
Date/Time
↵
button (the menu DISPLAY SIGNAL 2 will
appear on the display).
•
Select the desired measurement parame-
ter with the
Rate
↑
or
Store
↓
button.
•
Select the desired mode of operation with
the
Rate
↑
or
Store
↓
button.
•
Confirm the selection with the
Date/Time
↵
button (a dot will appear in
front of the respective measurement pa-
rameter when operating manually).
The 3B NET
log
™ device is ready to conduct
measurements.
8.5 Application as a handheld measuring
device with sensors
•
Set up the 3B NET
log
™ equipment.
•
Connect the sensor to the relevant input
and remove the connections of the 4-mm
sockets from the same channel.
