background image

14 

Digital Detection Module - Quick Guide 

 

www.2MTechnology.net 

 

Use a mains socket outlet with a protective earthing (grounding) connection. 

 

Ground your device properly if the device is intended to be grounded. 

Battery Use Caution 

 

When battery is used, avoid: 

 

High or low extreme temperatures during use, storage and transportation; 

 

Extremely low air pressure, or low air pressure at high altitude. 

 

Battery replacement. 

 

Use the battery properly. Improper use of the battery such as the following may cause risks 
of fire, explosion or leakage of flammable liquid or gas. 

 

Replace battery with an incorrect type; 

 

Dispose of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery; 

 

Dispose the used battery according to your local regulations or the battery manufacturer's 
instructions. 

Avertissement de l’utilisation de la batterie 

 

Lorsque utiliser la batterie, évitez: 

 

Températures extrêmement élevées ou basses pendant l’utilisation, le stockage et le 
transport; 

 

Pression d’air extrêmement basse, ou pression d’air basse à haute altitude. 

 

Remplacement de la batterie. 

 

Utilisez  la  batterie  correctement.  Mauvaise  utilisation  de  la  batterie  comme  celles 
mentionnées ici, peut entraîner des risques d’incendie, d’explosion ou de fuite liquide de gaz 
inflammables. 

 

Remplacer la batterie par un type incorrect; 

 

Disposer d’une batterie dans le feu ou un four chaud, écraser mécaniquement ou couper 
la batterie; 

 

Disposer la batterie utilisée conformément à vos règlements locaux ou aux instructions du 
fabricant de la batterie. 

 Regulatory Compliance 

 

FCC Statements 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 
Caution: The user is cautioned that changes or  modifications not  expressly approved by the 
party responsible for compliance could void the user's authority to operate the equipment. 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class A digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection  against  harmful  interference  when  the  equipment  is  operated  in  a  commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not  installed  and  used  in  accordance  with  the  instruction  manual,  may  cause  harmful 
interference to radio communications. Operation of this equipment in a residential area is likely 
to cause harmful interference in which case the user will be required to correct the interference 
at his own expense. 

 

LVD/EMC Directive 

Содержание 2MTHWT-HMD-II


















Отзывы: