background image

Model 408 NO Calibration Source Manual Rev. D-3 

WARRANTY STATEMENT

 

 
2B Technologies warrants its products against defects in materials and workmanship.  
2B  Technologies  will,  at  its  option,  repair  or  replace  products  which  prove  to  be 
defective.  The warranty set forth is exclusive and no other warranty, whether written 
or  oral,  is  expressed  or  implied.    2B  Technologies  specifically  disclaims  the  implied 
warranties of merchantability and fitness for a particular purpose. 

 

Warranty Periods 

 

The  warranty  period  is  one  (1)  year  from  date  of  receipt  by  the  purchaser,  but  in  no 
event more than thirteen (13) months from original invoice date from 2B Technologies. 

 

Warranty Service 

 

Warranty  Service  is  provided  to  customers  through  phone  support,  Monday  -  Friday, 
from  9:00  a.m.  to  5:00  p.m.,  Mountain  Time  USA  and  via  our  web-based  Technical 
Support  system  at 

https://twobtech.com/tech-support.html 

where  a  customer  support 

ticket may be logged.  In some cases the instrument may be repaired by the customer 
using parts supplied by 2B Tech.  If a customer repair is not possible or effective, the 
product  may  be  returned  to  2B  Technologies  for  repair  or  replacement.    Prior  to 
returning the product, a Returned Merchandise Authorization (RMA) number must be 
obtained from the 2B Technologies Service Department and an RMA form completed.  
The RMA form allows us to identify the owner of the instrument and provides a return 
shipping  address.    Please  do  not  return  any  of  the  accessories  (power  pack,  serial 
cable, connecting tubing, etc.) with the instrument. 

 

Shipping 

 

2B Technologies will pay freight charges for replacement or repaired products shipped 
to  the  customer.  Customers  shall  pay  freight  charges  for  all  products  returned  to  2B 
Technologies. 

 

Conditions 

 

The  foregoing  warranty  shall  not  apply  to  defects  resulting  from  improper  or 
inadequate  maintenance,  adjustment,  calibration  or  operation  by  the  customer.  
Maintenance,  adjustment,  calibration  or  operation  must  be  performed  in  accordance 
with  instructions  stated  in  the  Nitric  Oxide  Calibration  Source

  manual.    Usage  of 

maintenance materials purchased from suppliers other than 2B Technologies will void 
this warranty.

 

 

Limitation of Remedies and Liability 

 

The remedies provided herein are the Customer's sole and exclusive remedies.  In no 
event  shall  2B  Technologies  be  liable  for  direct,  indirect,  special,  incidental  or 
consequential  damages  (including  loss  of  profits)  whether  based  on  contract,  tort  or 

Содержание Model 408



























Отзывы: