1-CUBE SU 6.2. Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 13

1-CUBE SU 6.2. Скачать руководство пользователя страница 5

5

5.

U

SER

’

S GUIDE

Picture of the cooling bath - SU6.2:

Control panel

Mixer engine Removable top

Cooling thermostat

Cooling on-off switch

Cooling exchanger

Air inlet

First switch on the Main Switch located on the front panel of the equipment.

NOTICE:

It is forbidden to use the device without filling it with water. It could cause device destruction and staff injury.

The device warns you if there is not enough water inside the bath. It is necessary to use electrically conductive

liquid.

If wou use non electrically conductive

liquid then the device will notify all the time that there is not enough water

inside the bath even if it isn’t true. If you use distilled water in the laboratory just add a pinch of salt (NaCl) and you

will get electrically conductive

liquid.

Switch on the cooling on-off switch except for the main switch in the cooling bath. There is a cooling thermostat just

next to cooling on-off switch and we do reccomend to leave its value as preadjusted „value 5“

Warning! Do not exceed the temp30 degrees Celsius in the cooling bath otherwise the cooling system can

be irreversibly damaged!!!!!

«
...
3
4
5
6
7
...
»

Содержание SU 6.2.














Отзывы:

Нет отзывов