background image

WAYNE COMBUSTION SYSTEMS

801 GLASGOW AVE.

FORT WAYNE, IN 46803

ELECTRIC SHOCK HAZARD

OVERHEATING HAZARD

HIGH VOLTAGES ARE PRESENT IN THIS EQUIPMENT.
FOLLOW THESE RULES TO AVOID ELECTRIC SHOCK.

s

Use only a properly grounded circuit. A ground fault
interrupter is recommended.

s

Do not spray water directly on burner.

s

Turn off power before servicing.

s

Read the owner’s manual before using.

SHOULD OVERHEATING OCCUR:

s

Shut off the manual gas valve to the appliance.

s

Do not shut off the control switch to the pump or blower.

SPECIFICATIONS

FOR YOUR SAFETY

IF YOU SMELL GAS:

1.  OPEN WINDOWS
2.  DON’T TOUCH ELECTRICAL SWITCHES
3.  EXTINGUISH ANY OPEN FLAME
4.  IMMEDIATELY CALL YOUR GAS

SUPPLIER.

THESE INSTRUCTIONS SHOULD BE
AFFIXED TO THE BURNER OR
ADJACENT TO THE HEATING
APPLIANCE.

FOR SHIPPING PURPOSES, THE FLAME
SPREADER IS FULLY RETRACTED.  
FLAME SPREADER ADJUSTMENT IS
MANDATORY AND EFFECTS BURNER
IGNITION AND PERFORMANCE.

MODELS

P250AF

P265

P265EP

P250AFEP

P265F

P265DI

P250AFDI

P265FEP

GAS BURNER

Publication Date 5/01   -   Revision B   -   Manual 101220

NOTE:  Dimensions in (  ) are informational only.  English values take priority.

WARNING: If the information in these
instructions is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or death.

-

Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.

-

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone.  Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

-

Installation and service must be performed by a qualified
installer, service agency or the gas supplier.

CARBON MONOXIDE IS A COLORLESS, ODORLESS GAS
THAT CAN KILL. FOLLOW THESE RULES TO CONTROL
CARBON MONOXIDE.

s

Do not use this burner if in an unvented, enclosed area. Carbon
monoxide may accumulate.

s

Do not adjust the pressure regulator. High pressures produce
carbon monoxide.

s

Check flue gases for carbon monoxide. This check requires
specialized equipment.

s

Allow only qualified burner service persons to adjust the burner.

Special instruments and training are required.

s

Read the owner’s manual before using.

CARBON MONOXIDE

POISONING HAZARD

NOTICE

BURNER MODELS

MINIMUM INPUT

MAXIMUM INPUT

FUELS

P250AF & P250AF-EP & P250AFDI

50,000 BTU/Hr (14.65 kW/Hr)

250,000 BTU/Hr (73.27 kW/Hr)

Natural & L.P. Gas

P265 & P265EP

65,000 BTU/Hr (19.05 kW/Hr)

200,000 BTU/Hr (58.61 kW/Hr)

Natural & L.P. Gas

P265F & P265FEP

65,000 BTU/Hr (19.05 kW/Hr)

200,000 BTU/Hr (58.61 kW/Hr)

Natural & L.P. Gas

ELECTRICAL Power Supply - 115V/60HZ 1 Ph.

MOUNTING:  Adjustable Flange is Standard

Pedestal Mount is Optional.

Summary of Contents for P265DI



























Reviews: