background image

 

Rev. 6/12/2017 

CANT, MANUAL 

Copyright 2017 Vestil Manufacturing Corp. 

 

Page 1 of 8 

 

 
 

 

 
 
 
 
 

 

CANT-Series Cantilever Carts 

Instruction Manual 

 
 

 

 
 
 
 
 
 
 

 

Receiving instructions: 

 

  After delivery, remove the packaging from the product. Inspect the product closely to determine whether 
it sustained damage during transport. If damage is discovered, record a complete description of it on the 
bill of lading. If the product is undamaged, discard the packaging.

 

 

NOTE:

 

     The end-user is solely responsible for confirming that product design, installation, use, and maintenance 
comply with laws, regulations, codes, and mandatory standards applied where the product is used.

 

 
 

 

 

Table of Contents 

Specifications…………………………….………………………………………………………………………………………… 2 
CANT-3048 Exploded Parts View and Bill of Materials…...…………………………………………………………………… 2 
CANT-3060 Exploded Parts View and Bill of Materials………………………………………………………………………... 3 
CANT-3648 Exploded Parts View and Bill of Materials………………………………………………………………………... 3 
Signal words…………………………………………………………………………………………………………………………4 
Hazards of improper use………………………………………………………………..………………………………………… 4 
Assembling the cart……………………………………………………………………………………………………………..5 - 6 
Using the rack………………………………………………………………………………………………………………………. 6 
Inspections………………………………………………………………………………………………………………………….. 6 
Labeling diagram………………………………………………………..…………………………………………………………. 7 
Limited Warranty………..………………………………………………………………………………………………………….. 8 

 

Vestil Manufacturing Corp. 

2999 North Wayne Street, P.O. Box 507, Angola, IN 46703 

Telephone: (260) 665-7586    Toll Free (800) 348-0868 

Fax: (260) 665-1339 

www.vestilmfg.com    e-mail: 

H

U

[email protected]

U

 

Summary of Contents for CANT-Series









Reviews: