background image

 

 

 

Product Name: 

Cement Two Tier Pedestal Outdoor Fountain 

SKU #: 

WHF907 

 

Contact: [email protected] 

Instruction Manual 

Please save this manual for future reference. 

Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest 
standards of safety and quality.   

PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY. 

Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged 
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.   

 

CARTON CONTENTS: 

 

 

Description 

Accessories standards and type 

Quantity 

01  Fountain 

 

02  Pump w/ Adaptor 

 

 

Tools required for assembly:

 No tools required for assembly. 

 

Assembly Instructions:   

1.

 

Unpack the contents of the box and check to make sure that all items are accounted for and in good 
condition. 

2.

 

Select a flat, level surface for the assembly and final location of your fountain.   

3.

 

Place the fountain on a flat, level surface. From the opening at the back of the fountain base, insert the 

water supply tube into the pump outlet. Place the pump upright in the basin and draw the pump power cord 

out of the fountain back. Insert LED connector to cord with the pump and twist tight. 

(①)

 

4.

 

Add clean water into the basin. The water level should be approximately 30mm lower than the edge of the 

basin. (

②)

 

5.

 

Connect the 

pump power cord to a ground fault circuit interrupter (GFCI) outlet and the product will begin 

to function as intended. (

③)

 

6.

 

To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing 

after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area 

where it cannot be damaged.     

7.

 

Do not leave your fountain running for extended periods of time when no one is present to observe the 

performance. 

8.

 

Check the area around your fountain on a regular basis to ensure that there is no leakage. 

9.

 

Please refresh the fountain with water each week to ensure it in good condition. 

10.

 

Do not add any harmful chemicals to the water as it may alter the paint finish. 

 

Summary of Contents for WHF907

Page 1: ...ain on a flat level surface From the opening at the back of the fountain base insert the water supply tube into the pump outlet Place the pump upright in the basin and draw the pump power cord out of the fountain back Insert LED connector to cord with the pump and twist tight 4 Add clean water into the basin The water level should be approximately 30mm lower than the edge of the basin 5 Connect th...

Page 2: ...in water exceeding 30ºC 86ºF Do not use the pump in flammable liquids Do not use the pump for industrial purposes Do not use the pump in vehicles or on ships or aircraft or swimming pools Do not use the pump in location where special conditions prevail such as the presence of a corrosive or explosive atmosphere dust vapor or gas Do not let the pump run dry Pump must be completely submerged for pro...

Page 3: ...s and in a freeze area of the country ensure that all water is removed and the unit is completely dry This product is NOT to be operated below 41 5 freeze damage may occur WARNINGS 1 To reduce the risk of electric shock connect only to a properly grounded grounding type receptacle 2 To reduce the risk of electric shock use only on portable self contained fountains no larger than 5 feet in any dime...

Page 4: ...e impeller rotor assembly by gently pulling on the impeller blades Use a soft cloth or brush to clean the area inside of the pump where the impeller rotor assembly was Clean the inlet screen impeller housing impeller in warm soapy water Reassemble the pump and inspect for proper operation TIPS AND TROUBLESHOOTING 1 Ensure that the pump s flow control switch is set to maximum before operating Once ...

Reviews: