background image

© UPLIFT Desk

 • 1-800-349-3839 • [email protected] • www.upliftdesk.com

®

E3 Under Desk Exercise Bike Instructions

MVT003

MVT003/R02

Package contents

M8x50 bolt

(qty 4)

Main frame

Front foot

Pin

Back foot

Seat

Back post

Seat post

Back cushion

Right & Left pedals

Handlebars

M8 acorn nut

(qty 6)

Arc washer

(qty 6)

Flat washer

(qty 9)

Back height knob

M8 nut

(qty 3)

Back foot cover

M8x16 screw

(qty 4)

Wrench

M8x45 screw

(qty 2)

Allen wrench

Step 1

Unfold the bike so that it rests upright on the floor with both legs 

steady on the ground. Then insert the pin into the middle hole at the 
axis of the Main frame.

Step 2

Attach the Front foot with two (2) M8x50 bolts and two (2) Arc 
washers and lock them in place with two (2) M8 acorn nuts.  
Tighten using the Wrench. 

Attach the Back foot to the Main frame with two (2) M8x50 bolts 
and two (2) Arc washers and lock them in place with two (2) M8 
acorn nuts. Finish by clipping the Back foot cover over the Back 
foot.

Step 3

It’s now time to thread the wires for the heart rate monitor through 
the back and seat of the bike. Insert the lower wires of the Back post 
into the large hole on the Seat post and feed them through to the 
opening at the bottom. When you start to see the wires come out of 
the bottom, hold the wire end still, and slide the Seat post up closer 
to the Back post to reduce the slack between the parts. 

NOTE: Be careful to not pull the top end of the wire inside the Back 
post. Both ends of the wire should be accessible.

Align the holes as shown, and insert four (4) M8x16 screws and four 
(4) Flat washers, and tighten using the Allen wrench.

Step 4

Connect the wires on the Handlebars to the top end of the wires in 
the Back post. Hold on to the lower end of the wires and pull it in 
enough to bring the Handlebar and Back post together and attach 
using two (2) M8x45 screws, two (2) Arc washers, and two (2) M8 
nuts and tighten using the Wrench.

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 sc

erws

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 scerws

+4 sc

er

ws

+4 scer

ws

+4 scerws

+4 scerws

+4 scerws

Summary of Contents for MVT003

Page 1: ...r the Back foot Step 3 It s now time to thread the wires for the heart rate monitor through the back and seat of the bike Insert the lower wires of the Back post into the large hole on the Seat post and feed them through to the opening at the bottom When you start to see the wires come out of the bottom hold the wire end still and slide the Seat post up closer to the Back post to reduce the slack ...

Page 2: ... Each foot s pedal straps can be adjusted to fit different users feet sizes NOTE Pedaling backwards will loosen pedals Step 5 Connect the wires from the Main frame to those in the seat and back assembly Tuck all the wires down into the Main frame Insert the seat assembly by pulling the Seat height knob out squeeze the spring loaded balls on the Seat post together and slide the Seat post into the M...

Page 3: ...e data to zero by pressing the Mode Key for several seconds To reset the odometer remove and replace the batteries The processor turns off automatically when the spin sensor has no signal input or no key is pressed for approximately 4 minutes The LCD Display can be activated again by pressing the Mode Key or by rotating the pedals Modes SCAN Scans through all functions TMR Timer SPD Speed MPH DIS ...

Page 4: ...nce pain or you feel faint short of breath or dizzy stop exercising and consult a physician Incorrect or excessive use of this machine can result in injury CAUTION This machine is not a toy Keep children away from this exercise bike espe cially while in use Children should be taught to never put their fingers near any moving parts on this machine CAUTION Your exercise bike should be operated on a ...

Reviews: