background image

Universal Remote Control, Inc.

www.universalremote.com

OEE-0017D Rev 03(05/14/02)

This remote control is preprogrammed
to operate CABLE Box. 
Please program it for your TV by
following the instructions shown below.

The remote control uses AAA batteries.
Please be sure to match the batteries
with the (+) and (- ) markings inside the
battery compartment during installation.

The remote control is preprogrammed to
control VOLUME and MUTE functions
through your TV. To switch VOLUME and
MUTE functions to your Cable Box:

STEP1

Press [      ] and [MUTE]
buttons simultaneously until
red light is on.

STEP2 

Press [] button.

STEP3

Press [            ] button. 

To return to the TV’s VOLUME, press
[TV POWER] button.

*Tip: 

Red light will blink twice.

Set-up for advanced functions

A. To turn on your TV and Cable at the

same time with  

button:

STEP1

Press [        ] and [0] buttons
simultaneously until the red
light is on.

STEP2

Press [CH +] button. 

Set-up for your Cable Box

The remote control is preprogrammed
to control your cable box. If it does
not work properly, please set-up the
right code by using the three-digit
code or searching method.
If you have a TV with a remote
control, we recommend that you plug
its power cord directly into a wall
outlet if available (your cable installer
may select an alternate setup)

Operation

If red light does not blink when
you press keys the operation is
intermittent:

Make sure the batteries are inserted
correctly.
Replace old batteries with two new
AAA batteries. Please do not mix old
batteries with new ones. 

Operating Manual 

for 2 in 1 Cable TV 

Remote Control

UR-J550TVE

Instructions

Batteries

Programming your remote control

Set-up for your VOLUME control 

Helpful hints

STEP3

Point the remote control toward
the TV and enter the three-digit
code from the code table. If
there is more than one code
number assigned to your TV
brand, try one code number at a
time until the TV turns off right
after you entered the number.

Searching Method

Press [CH +] button and hold until the
TV turns off. As soon  as the TV turns
off, release [CH+] button. 

*Tip :

You can confirm the power off and
on by pressing [MUTE] button.

STEP4 

Press [TV POWER] button to
store the three-digit code.

*Tip:

Red light will blink twice. 

Three-digit code : 

Setup for your cable box

No setup is required. The remote control is
preprogrammed to operate your cable box.

Setup for your TV

Find your TV brand and its three-digit
code on the back of this manual. If the
TV brand is not listed, please use the
Searching Method in  

STEP3  

.

STEP1

Turn on your TV manually. 

*Tip : 

If you have RCA TV, don’t turn
on the TV.

STEP2 

Press [TV POWER] and  [MUTE]
buttons simultaneously until the
red light is on.

*Tip: 

Red light will blink twice

The [          ] button sends out the TV
and CABLE power commands if you
press the [             ] button.

To return to the original function, press
the [CH-] button in the   

STEP2   

.

B.  Recalling the TV Three-digit  code :

STEP1

Press [TV POWER] and [MUTE]
buttons simultaneously until the
red light is on.

STEP2 

Press [VOLUME -] button.

The red light will blink a number of
times indicating the number of each
digit of the code. Each digit is
separated by one second interval of
red light being off.

*Tip: 

One blink, three blinks and 10
blinks, indicates the code
number 130.

Press  arrow  gently  & 
pull  down  to  remove cover

Install  two  AAA  alkaline
batteries  as  shown  here

Reviews: