background image

Form No. 3405-472 Rev A

ExcelaRate Upgrade Kit

Multi Pro

®

5800 Turf Sprayer

Model No. 41642

Installation Instructions

WARNING

CALIFORNIA

Proposition 65 Warning

This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Safety

WARNING

Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals,
plants, soils, or other property.

Carefully read and follow the chemical warning labels and material safety data sheets (MSDS) for all
chemicals used and protect yourself according to the chemical manufacturer's recommendations. For
example, use appropriate personal protective equipment (PPE), including face and eye protection,
gloves, or other equipment to guard against personal contact with a chemical.

There may be more than 1 chemical used and information on each chemical should be assessed.

Refuse to operate or work on the sprayer if this information is not available.

Before working on a spray system, ensure that the system has been triple rinsed and neutralized
according to the recommendations of the chemical manufacturer(s) and that all the valves have been
cycled 3 times.

Verify that there is an adequate supply of clean water and soap nearby, and immediately wash off any
chemicals that contact you.

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Description

Qty.

Use

Pressure transducer

1

Cap fitting

1

Flange gasket

1

Flow meter

1

Flow meter gasket

2

Switch

1

Wire harness

1

Install the kit.

© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3405-472* A

 

Summary of Contents for 41642

















Reviews: