background image

Copyright © 2007, Tjernlund Products, Inc.  All rights reserved.

P/N8500702

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794

PHONE (651) 426-2993 • (800) 255-4208 

FAX (651) 426-9547

www.Tjernlund.com

REV. B 

TJERNLUND SPECIFIED SYSTEMS

START-UP GUIDE 

AND WARRANTY ACTIVATION FORM

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED, LICENSED
SERVICE PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND
OPERATION OF THIS UNIT.  READ THIS GUIDE THOROUGHLY BEFORE
ATTEMPTING INSTALLATION OR OPERATION.  FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN IMPROPER INSTALLATION,  ADJUSTMENT,
SERVICE OR MAINTENANCE POSSIBLY RESULTING IN FIRE, ELECTRICAL
SHOCK, CARBON MONOXIDE POISONING, EXPLOSION, OR PERSONAL
INJURY OR PROPERTY DAMAGE.

DO NOT DESTROY.  PLEASE READ CAREFULLY AND

KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

INTRODUCTION: Completion of all the steps contained in this guide will verify that the all
Tjernlund Specified System products are operating properly.  Follow the directions carefully;
step by step completion ensures thoroughness and allows Tjernlund to provide better support if
difficulties occur.  This guide is normally completed in 15 minutes.

Upon completing the guide, please complete the attached warranty form and fax or mail a com-
pleted copy of the entire guide to Tjernlund Products.

IMPORTANT:

IN ORDER TO ACTIVATE THE WARRANTY FOR ANY

TJERNLUND SPECIFIED SYSTEM PRODUCT THIS GUIDE MUST BE 
COMPLETED AND RETURNED TO TJERNLUND PRODUCTS ALONG WITH
THE INCLUDED WARRANTY ACTIVATION FORM.

Summary of Contents for CPC-2

















Reviews: