background image

Installation, Operation and 

Maintenance 

 

   DLSC-IOM-1.0 

4-23-20 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Low Profile, Series FanPowered Terminal Unit with 

Sensible Cooling Coil 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Model: DLSC Rev A 

 

 

 

This IOM is meant to demonstrate general dimensions and information of this product. The drawings are not meant to detail every aspect of the product. Drawings are not to scale. 

Titus reserves the right to make changes without written notice. 

All rights reserved. No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system without permission in writing from Tomkins Industries, Inc. 

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, 
and air-conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or 
altered equipment by an unqualified person could result in death or serious injury. When working on the equipment, observe all 
precautions in the literature and on the tags, stickers, and labels that are attached to the equipment. 

SAFETY WARNING 

Summary of Contents for DLSC


















Reviews: