background image

INCLUDED IN YOUR PACKAGE

Cordless Handset

AC Adapter

Base Unit

User Guide

NiMH Battery

10-foot, 4-wire RJ-11 Line Cord

Rubber Battery Screw Cover

15-foot, 8-wire RJ-45 Cable

Phillips Screw

Clear Plastic Overlay

PREPARING TO USE THE DC9100 SERIES

1. Prepare to install the battery into the cordless handset by 

firmly pressing down on the top of the battery cover and 
sliding it off. If cover is secured with a screw, remove the 
screw first.

2. Locate the lightly embossed numbers “1” and “2” on the

battery’s plastic connector.

3. Insert the battery connector into the handset’s connector 

with the embossed numbers facing up.

Note: The handset may “beep” when the battery is connected. This is not
an indication that the telephone is ready to use. To obtain optimal perform-
ance of the telephone, be sure to charge the battery for 15 to 20 hours

.

4

. Replace the battery compartment cover and retaining screw.

5. Insert the provided rubber screw cover.
6. Turn the telephone base so the back panel is facing you.

Insert either end of the RJ-45 cable into the jack on the back 
of the telephone labeled 

LINE

.

7. Insert the other end of the cable into the jack on the AC 

adapter labeled 

PHONE

.

8. Insert one end of the RJ-11 line cord into the jack on the AC 

adapter labeled 

LINE

.

9. Insert the other end of this line cord into a telephone jack.
10. Plug the AC adapter into an unswitched electrical outlet.
11. Once your telephone is connected, remove the plastic

overlay and place the paper faceplate over the keys. Replace 
the plastic overlay by hooking the tabs on the overlay into 
the recessed slots located on both sides. The overlay is
easiest to insert when the left or right side tabs are inserted 
first, and the middle of the overlay is slightly bowed to allow
for insertion of the other tabs.

12. Place the cordless handset on the base unit.

CHARGING THE BATTERY

The rechargeable Nickel Metal Hydride (NiMH) battery must be
fully charged before using the phone for the first time. It is recom-
mended that that battery pack be charged for approximately 15
to 20 hours, without interruption, before use. To charge the battery,
place the handset, keypad down, in the base unit. Make sure the

CHARGE

LED on the base lights. If the LED does not light:

1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is not plugged into a switched

electrical outlet.

3. Ensure that the handset charging contacts at the bottom of 

the handset are making good contact with the base unit’s 
charging contacts.

CLEANING THE BATTERY CONTACTS

To maintain a good charge, it is important to clean all charging
contacts on the handset and base unit. Use a pencil eraser or
other contact cleaner.

Do not use any liquids or solvents.

BATTERY SAFETY INSTRUCTIONS

1. Use only Teledex-approved battery replacements.
2. Dispose of used batteries according to local codes pertaining

to NiMH batteries.

3. Do not dispose of batteries in fire, as they may explode
4. Charge the telephone's batteries only while in the telephone 

handset, and only by using the telephone base unit to charge.
Do not attempt to remove the batteries and charge them in 
a separate charging unit.

5. Do not short-circuit the battery pack, as this may cause it to 

explode or catch fire.

HANDSET/BASE REGISTRATION PROCEDURE

This procedure establishes an exclusive link between a specific
handset and base, thereby allowing no other access to this
specific base. To accomplish this procedure, place the handset
on the base in the charging position. The 

LINE 

indicator will

blink while the process is occuring. This process occurs each
time the handset is placed on the base in the charging cradle.

ADJUSTING THE RING VOLUME

The up and down volume keys will adjust the ringer volume of
the telephone. Additionally, the DC9100 series telephone has an
optional “courtesy” ring mode, wherein the ring volume begins
at the lowest setting, then automatically rings louder with each
successive ring during an incoming call. To select the courtesy
ring mode, follow these steps:

Press the 

FLASH

key; then the 

4

key; then the 

STORE

key; then

the 

1

key.

To return to regular ring mode: Press the 

FLASH

key; then the 

1

key; then the 

STORE

key; then the 

1

key.

ADJUSTING SPEAKERPHONE VOLUME

The speakerphone has eight (8) levels. To adjust speakerphone
volume, locate the volume up/down keys, located on the front
surface of the phone below the keypad. With the speaker active,
press the “down” arrow key to decrease the volume level, and
press the “up” arrow key to increase it.

RESTORE THE PRODUCT TO NORMAL OPERATION.

- IF THE PRODUCT HAS BEEN DROPPED OR THE CABINET HAS BEEN

DAMAGED.

- IF THE PRODUCT EXHIBIT A DISTINCT CHANGE IN PERFORMANCE.

10. AVOID USING A TELEPHONE (OTHER THAN A CORDLESS TYPE)
DURING AN ELECTRICAL STORM. THERE MAY BE A REMOTE RISK OF
ELECTRIC SHOCK FROM LIGHTNING.
11. DO NOT USE THE TELEPHONE TO REPORT A GAS LEAK IN THE
VICINITY OF THE LEAK.

PLEASE SAVE THESE INSTRUCTIONS

DC9100 SERIES DIAGRAM

DC9100 SERIES USERS GUIDE

900 MHz Single-Line Digital Cordless Guestroom Telephone

Part Number 600-0480-66A                Copyright © 2004  Teledex LLC. ALL RIGHTS RESERVED.

Telephone

(408) 363-3100
(800) 794-8353

Internet

www.teledex.com
store.teledex.com

Email

[email protected]

Mailing Address

6311 San Ignacio Avenue
San Jose, CA  95119 USA

CONTACTING TELEDEX

RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK WHEN
THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE FOLLOW-
ING CONDITIONS:

- WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED OR FRAYED.
- IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
- IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
- IF THE PRODUCT DOES NOT OPERATE NORMALLY BY FOLLOWING

THE OPERATING INSTRUCTIONS. ADJUST ONLY THOSE CONTROLS THAT
ARE COVERED BY THE OPERATING INSTRUCTIONS, AS IMPROPER
ADJUSTMENT OF OTHER CONTROLS MAY RESULT IN DAMAGE, AND
MAY REQUIRE EXTENSIVE WORK BY A QUALIFIED TECHNICIAN TO

Reviews: