GUIDA ALL’INSTALLAZIONE
INSTALLATION GUIDE
IT - Istruzioni originali
EN - Original instructions
TCODE
73.95
40
86.71
D-MNL0TCODE
23-11-2020 - R
ev
.02
73.95
40
86.71
1 2
1 2 3 4 5 6 7 8
TCODE
TCODE-B
1 2 3 4 5 6 7 8
TCODE-B
12 Vdc o
24 Vac
L1 = led rosso
L2 = led verde
P1
Uscita
N.A. - CH.A
Uscita
N.A. - CH.B
+ -
1 2
1 2 3 4 5 6 7 8
TCODE
TCODE-B
1 2 3 4 5 6 7 8
TCODE-B
12 Vdc o
24 Vac
L1 = led rosso
L2 = led verde
P1
Uscita
N.A. - CH.A
Uscita
N.A. - CH.B
+ -
1 2
1 2 3 4 5 6 7 8
TCODE
TCODE-B
1 2 3 4 5 6 7 8
TCODE-B
12 Vdc o
24 Vac
L1 = led rosso
L2 = led verde
P1
Uscita
N.A. - CH.A
Uscita
N.A. - CH.B
+ -
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 4a
Fig. 5
Via Enrico Fermi, 43 - 36066 Sandrigo (VI) - Italy
Tel +39 0444 750190 - Fax +39 0444 750376
[email protected] - www.tauitalia.com
3_ Enter the Master code and then press the button
7 to beep when the buttons are pressed.
4_ Enter the Master code and consequently press
the 9 key to never beep when the keys are
pressed.
2_ Press button
A
for 4 sec. until you hear a “beep”
and the green led starts to flash;
3_ While the green LED is flashing, enter the code
you want to delete (2 ÷ 8 digits);
4_ Then press button
B
for 4 sec. until you hear a
“beep” and the LED starts flashing red and green to-
gether and then briefly press button
B
again. At this
point, to confirm code deletion, the red and green
LED will stop flashing.
6. DELETING ALL CODES
If you wish to return the keypad to factory condi-
tions without any code entered, proceed as follows:
1_ Short press the P1 button on the TCODE-B
decoder. The green led starts flashing and you will
have one minute to enter the new code.
2_ Press button
A
for 4 sec. until you hear a “beep”
and the green led starts to flash;
3_ While the green LED is flashing, enter the Master
code (if factory = 0000; or the one created by you).
4_ Then press button
B
for 4 sec. until you hear a
“beep” and the LED starts flashing red and green to-
gether and then briefly press button
B
again. At this
point, to confirm codes deletion, the red and green
LED will stop flashing.
7. CHANGING THE MASTER CODE
To change the Master code, follow these steps:
1_ Short press the P1 button on the TCODE-B
decoder. The green led starts flashing and you will
have one minute to enter the new code.
2_ Press button
A
for 4 sec. until you hear a “beep”
and the green led starts to flash;
3_ While the green LED is flashing, enter the Master
code (if factory = 0000; or the one created by you).
4_ Press button
A
again for 4 sec. until you hear a
“beep” and the green LED starts flashing quickly;
5_ While the green LED is flashing quickly enter the
new Master code;
6_ Then press button
B
briefly, a “beep” will be
heard and the green LED will remain on for a second
confirming that the new code has been entered.
8. KEYBOARD SETTINGS
You can change the keyboard settings by doing the
following:
1_ Enter the Master code and consequently press
key 4 to always have the backlighting of the keys.
2_ Enter the Master code and consequently press
the button 6 to have the backlighting of the but-
tons only when they are pressed.
