background image

   

WC3-SP82K

Textron Wildcat XX

Side 8” Subwoofer Pods

!

Please read and understand these 

instructions completely before 

installation to avoid possible injury, or 

damage to the accessory or vehicle. 

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. 

All SSV Works Electronics are covered by a limited 1 year warranty against defects in material or workmanship. 

All Kicker Speakers are covered by a limited 1 year warranty against defects in material or workmanship. All 

Kicker Amplifiers are covered by a limited 2 year warranty against defects in material or workmanship. Labor for 

replacement of defective components is not covered. Contact SSV Works for further warranty information.

TOOLS FOR INSTALLATION

PARTS LIST IMAGES

3.    

M6 Hex Head Bolts & 

Washers x4

11.    M6x1.0 screw & nut x1

7.    

Large Washer x4

4.   

Backet “A” x2

8.  

 Loaded amp tray with Kicker 

500.1 amp

12.   M5 screw x4

2.   M6 x 1.0 Screws and 

Washers x12

10.   B-H1912 24” audio extension 

harness x1 and 

B-H1389 69” 

audio extension harness x1 

6.   Driver/Passenger Brackets

D

R

I

V

E

R

P

A

S

S

E

N

G

E

R

1.   

Driver & Passenger Subs - Pair

9.   

Amp power wire x1, 

Fuse 

Holder with 40A Fuse and 

Battery Terminal Cable x1

 

5.   

Bracket “B” x2

- T25 & T30 Torx - 8mm socket   - 8mm & 10mm wrench  

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com     |     Phone: 818-991-1778     |     Fax: 866-293-6751

For ease of installation, we recommend removing the Stage 1 kick panel 6.5” speaker pods from the vehicle prior to installing the 

WC3-SP82K. If you do not have the 6.5” speaker pods installed in your vehicle, skip to Step D.

- #2 Phillips screwdriver  - Wire cutters

Summary of Contents for WC3-SP82K









Reviews: