background image

SERVICE MANUAL

Sony Corporation

Published by Sony Techno Create Corporation

SPECIFICATIONS

9-896-020-01

2014F33-1

© 

2014.06

US Model

Ver. 1.0  2014.06

Model Name Using Similar Mechanism

MEX-GS610BT

Mechanism Type

MG-101CF-188

Optical Pick-up Name

DAX-25A

•  The tuner and CD sections have no adjustments.

 AUDIO SYSTEM

The service manual of the mechanism deck, used in 
this model, has been issued in a separate volume. 
Please refer to the service manual of the MG-101 
series for the mechanism deck information.

Photo: MEX-GS810BH

MEX-GS810BH/N6000BH

AUDIO POWER SPECIFICATIONS

CEA2006 Standard
Power Output: 17 Watts RMS × 4 at 4
Ohms < 1% THD+N
SN Ratio: 80 dBA 
(reference: 1 Watt into 4 Ohms)

Tuner section

FM

Tuning range: 87.5 – 107.9 MHz
Antenna (aerial) terminal: 

External antenna (aerial) connector

Intermediate frequency: 25 kHz
Usable sensitivity: 8 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio (stereo):

79 dB (Conventional broadcast)
80 dB (HD Radio broadcast)

Separation at 1 kHz:

50 dB (Conventional broadcast)
80 dB (HD Radio broadcast)

Frequency response:

20 - 15,000 Hz (Conventional broadcast)
20 - 20,000 Hz (HD Radio broadcast)

AM

Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal: 

External antenna (aerial) connector

Intermediate frequency: 

9,115 kHz or 9,125 kHz/5 kHz

Sensitivity: 26 μV

CD Player section

Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
Corresponding codec: MP3 (.mp3) and WMA (.wma)

USB Player section

Interface: USB (High-speed)
Maximum current: 

MEX-N6000BH: 1 A
MEX-GS810BH: 1 A (front), 2.1 A (rear)

The maximum number of recognizable tracks: 

10,000

Corresponding codec: 

MP3 (.mp3), WMA (.wma) and WAV (.wav)

Wireless Communication

Communication System: 

BLUETOOTH Standard version 3.0

Output: 

BLUETOOTH Standard Power Class 2 
(Max. +4 dBm)

Maximum communication range: 

Line of sight approx. 10 m (33 ft)*

1

Frequency band: 

2.4 GHz band (2.4000 – 2.4835 GHz)

Modulation method: FHSS
Compatible BLUETOOTH Profiles*

2

:

A2DP (Advanced Audio Distribution Profile) 1.3
AVRCP (Audio Video Remote Control Profile) 1.5
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile)
SPP (Serial Port Profile)
MAP (Message Access Profile)
HID (Human Interface Device Profile)

*1 The actual range will vary depending on factors such 

as obstacles between devices, magnetic fields 
around a microwave oven, static electricity, 
reception sensitivity, antenna (aerial)’s performance, 
operating system, software application, etc.

*2 BLUETOOTH standard profiles indicate the purpose 

of BLUETOOTH communication between devices.

Power amplifier section

Output: Speaker outputs
Speaker impedance: 4 – 8 ohms
Maximum power output: 55 W × 4 (at 4 ohms)

General

Outputs:

Audio outputs terminal (front, rear, sub)
Power antenna (aerial)/Power amplifier control 

terminal (REM OUT)

Inputs:

SiriusXM input terminal
Remote controller input terminal
Antenna (aerial) input terminal
MIC input terminal
AUX input jack (stereo mini jack)
USB port:

MEX-N6000BH: front
MEX-GS810BH: front, rear

Power requirements: 12 V DC car battery (negative 

ground (earth))

Dimensions: 

Approx. 178 mm × 50 mm × 177 mm 
(7 

1

/

8

 in × 2 in × 7 in) (w/h/d)

Mounting dimensions: 

Approx. 182 mm × 53 mm × 160 mm 
(7 

1

/

4

 in × 2 

1

/

8

 in × 6 

5

/

16

 in) (w/h/d)

Mass: Approx. 1.2 kg (2 lb 11 oz)
Package contents:

Remote commander (1): RM-X231
Microphone (1)
Parts for installation and connections (1 set)

Design and specifications are subject to change 
without notice.

Summary of Contents for MEX-GS810BH

























































Reviews: