Solar Roofs SkyLine 200152C80EX Installation Manual Download

Page: 1 / 31

Wholly owned by ACR Solar International Corp.

5840 Gibbons Dr. Suite G Carmichael, CA 95608 (916) 481-7200

! " #$

% ! " #

& ! " #

' ( %

INSTALLATION MANUAL

August, 2005

The solar energy system described by this manual, when properly installed and maintained meets the

minimum standards established by the Solar Rating and Certification Corporation (SRCC). This

certification does not imply endorsement or warranty of this product by SRCC.

(Note: SkyLine formerly Fireball)

CONGRATULATIONS!

Thank you!

You have just purchased the most attractive and easiest to install active solar water heater

made! We have worked on every detail to assure you that SolarRoofs water heater will completely satisfy

you in its very high level of performance and dependability.

Table of Contents

SUBJECT

SECTION

Tools and Materials………………………………………………………………………1.0.

Systems, Components, Options and Diagram ……………………………………..2.0.

Specifications and Schematics………………………………………………………...2.1.

Antifreeze Safety Data:……………………………………….………………………….2.1.1

Components included with system……………………………………………………2.1.2

Important Notes……………………………………………………………………………2.2.

Collector Location, Orientation and Tilt………………………………………………3.0.

Overview of the Basic Installation Steps………………………………………….….4.0.

Assembling the Collector (Split Kits Only)………………………………….……….5.0.

Collector Installation……………………………………………………………………..6.0.

Determining the Best Pipe Run…………………………………………………….…..7.0.

Making Line Connections……………………………………………………………….8.0.

Control Component Details……………………………………………………….…….9.0.

Tank Connections……………………………………………………………………….10.0.

Charging the Solar Loop……………………………………………………………….11.0

Questions and Answers………………………………………………………………..12.0.

Certifications……………………………………………………………………………..12.1.

PLEASE CALL SolarRoofs.com WITH QUESTIONS

Toll Free USA Technical Install Help Number: (888) 801-9060

NOTE:

Installation Color Photo Sheets Accompany this Manual for You to Refer to.

Generally drawings or diagrams are at the end of their respective sections.

WE WELCOME YOUR COMMENTS!

We have worked to make SolarRoofs installation instructions easy

and complete. We are always looking to make them better and

welcome your comments and suggestions!

Summary of Contents for SkyLine 200152C80EX
































Search results

Summary of Contents for SkyLine 200152C80EX

Reviews:

Related manuals for SkyLine 200152C80EX

Brands by name

Popular brands

Solar Roofs SkyLine 200152C80EX, Installation Manual

Search results

Summary of Contents for SkyLine 200152C80EX

Reviews:

Related manuals for SkyLine 200152C80EX

Brands by name

Popular brands