background image

 
 

 

 

Page 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MI00446-28-EN 

SENECA s.r.l. 

Via Austria 26, PADOVA 

– ITALY 

Tel. +39.049.8705355 

– 8705359 Fax. +39.049.8706287 

Web site: 

www.seneca.it   

Customer service: 

[email protected]

 (IT), 

[email protected]

 

(Other)

 

Commercial information

[email protected]

 (IT)

[email protected]

 

(Other)

 

This  document  is  property  of  SENECA  srl.  Duplication  and  reproduction  of  its  are  forbidden 
(though  partial),  if  not  authorized.  Contents  of  present  documentation  refers  to  products  and 
technologies described in it. Though we strive for reach perfection continually, all technical data 
contained in this document may be modified or added due to technical and commercial needs; 

it’s  impossible  eliminate  mismatches  and  discordances  completely.  Contents  of  present 
documentation  is  anyhow  subjected  to  periodical  revision.  If  you  have  any  questions  don’t 

hesitate to contact our structure or to write us to e-mail addresses as above mentioned. 

 

USER MANUAL 

Z-GPRS3, Z-UMTS, Z-LOGGER3,  

Z-LTE, Z-LTE-WW 

Multi-protocol Datalogger, RTU, with Ethernet, modem 2G/3G/4G,  

GNSS and embedded I/O 

Summary of Contents for Z-GPRS3























































Reviews: