background image

WARNING: 

To reduce the 

risk of injury, the user must read and 

understand the operator’s manual 

before using this product.

ADVERTENCIA:

 

Para reducir 

el riesgo de lesiones, el usuario debe 
leer y comprender el manual del 
operador antes de usar este producto. 

AV E RT I S S E M E N T   : 

Pour réduire les risques de blessures, 

l’utilisateur doit lire et veiller à bien 

comprendre le manuel d’utilisation avant 

d’employer ce produit.  

 General Power Tool  

Safety Warnings ..............................2-3

 Drill Safety Warnings ..........................3

 

Symbols ..............................................4



 Electrical .............................................5



 Features ..............................................6



 Assembly .........................................6-7

 Operation .........................................7-8

 Maintenance .......................................9

 Warranty ...........................................10

 Figures (Illustrations) ...................11-12

 Parts Ordering  

and Service .........................Back page

 Règles de sécurité générales  

relatives aux outils électriques ........2-3

 Avertissements de sécurité relatifs 

perceuse ............................................3

 

Symboles ............................................4

 Caractéristiques électriques ...............5

 Caractéristiques .................................6

 Assemblage .....................................6-7

 Utilisation  ........................................7-8

 Entretien .............................................9

 Garantie ............................................10

 Figures (illustrations) ....................11-12

 Commande de pièces  

et dépannage ....................Page arrière

  Advertencias de seguridad 

para herramientas eléctrica ........... 2-3

  Advertencias de seguridad taladro ....3

 

Símbolos ............................................4

  Aspectos eléctricos ...........................5

 Características ...................................6

 Armado .......................................... 6-7

 Funcionamiento ............................. 7-8

 Mantenimiento ...................................9

 Garantía ...........................................10

  Figuras (illustraciones) ............... 11-12

  Pedidos de  

piezas y servicio ...........Pág. posterior

OPERATOR’S MANUAL

1/2 in. MUD MIXER/DRILL 

R7122

SAVE THIS MANUAL FOR 

FUTURE REFERENCE

CONSERVER CE MANUEL 

POUR FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL 

PARA FUTURAS CONSULTAS

INCLUDES: Mud Mixer/Drill, Auxiliary 
Handle, Chuck Key, Operator’s Manual 

****************

TABLE OF CONTENTS

INCLUT : Mélangeur de boue/perceuse, 
poignée auxiliaire, clé à mandrin, manuel 
d’utilisation

****************

TABLE DES MATIÈRES

INCLUYE: Mezcladora de lodo/taladro, 
mango auxiliar, llave del portabrocas, 
manual del operador

****************

ÍNDICE DE CONTENIDO

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for R7122












Reviews: