Rand-Kar X-AIR HANUMAN 602T AP User Manual Download

Page: 1 / 55

2008, october, 17

-User’s Manual

Section 1 to 7

-Maintenance Manual

Section 8

-Engine Manual

Annex

X-AIR

« HANUMAN »

X-AIR HANUMAN 602T AP

(with Rotax 582 and parachute)

X-AIR HANUMAN 602T SP

(with Rotax 582 without parachute)

X-AIR HANUMAN JABIRU AP

(with Jabiru 2200 and parachute)

X-AIR HANUMAN JABIRU SP

(with Jabiru 2200 without parachute)

X-AIR HANUMAN 912 AP

(with Rotax 912 and parachute)

X-AIR HANUMAN 912 SP

(with Rotax 912 without parachute)

X-AIR HANUMAN 912S AP

(with Rotax 912S and parachute)

X-AIR HANUMAN 912S SP

(with Rotax 912S without parachute)

RAND-KAR sa Canal de la Martinière 44320 Frossay - France Tél.:+33 (0) 240 642 166 Fax : +33 (0) 240 641 522

Société au capital de 46 000 € siret : 384.220.695.00017 RM 44 APE 353 B FR 39.384.220.695

http///www.randkar.fr

E-mail :

[email protected]

support technique

[email protected]

Summary of Contents for X-AIR HANUMAN 602T AP
























































Search results

Summary of Contents for X-AIR HANUMAN 602T AP

Reviews:

Related manuals for X-AIR HANUMAN 602T AP

Brands by name

Popular brands

Rand-Kar X-AIR HANUMAN 602T AP, User Manual

Search results

Summary of Contents for X-AIR HANUMAN 602T AP

Reviews:

Related manuals for X-AIR HANUMAN 602T AP

Brands by name

Popular brands