manualshive.com logo in svg
background image

CB-1 

 1 

Ramsey Electronics Model No.             CB1 

Getting tired of repeating yourself? Find yourself saying the 
same thing over and over? Here's the answer to your prayers!  
This kit will repeat your voice with amazing clarity over and 
over, without ever getting tired, in a number of different ways!  
Not only that, it preserves your voice even when the power is 
turned off. 

       

• 

20 seconds of recording time available in five, four second 

messages.  Messages can be combined for longer record and 
playback times. 

 
       

• 

Loud 2 Watt audio output. 

 
       

• 

Very clean, low noise “DAST” storage technology provides 

excellent audio quality. 

 
       

• 

Seven modes of operation available.  Even interfaces to radios 

and computers too! 

 
       

• 

Fully microprocessor controlled for easy use, no diodes to add - 

no dip switches to set.  Easy and fun to use! 

 
       

• 

LED displays show addresses and modes quickly, no guesswork. 

 
       

• 

Compatible with most  transceivers and works with most radio 

mikes. It will even key your radio with your message. 

 

• 

Can be used for: memos, HAM contesting, real estate sales, 

leaving the kids messages, CB radio...possibilities are unlimited!

 

CB1 CHATTERBOX 
VOICE RECORDER 

Содержание CB1 CHATTERBOX
























Отзывы: