background image

 

Version 14.02.2018 

HW:

 

GD(V97)/(V33) 

RL3-MIB4 

r.LiNK 

Video inserter 

 

RL3-MIB-4 

 

Compatible with VAG infotainment systems from MIB/MIB2/MIB II 

construction kits - High und Standard executions  

 

Compatible with Audi vehicles with MMI ( on MIB base) 

Bentley vehicles with MIB with 8“ monitor 

Lamborghini vehicles with MIB with monitor in instrument 

Porsche vehicles with PCM 4.0 

Seat vehicles with Media System Plus – navigation system PLUS 

Skoda vehicles with Columbus, Amundsen and Bolero 

VW vehicles with Discovery Pro, Discover Media, Composition Media 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Video-inserter for one rear-view camera and two more video inputs 

 
 
 

Product features 

 

 

Video-inserter for factory-infotainment systems 

 

CVBS Input for one rear-view camera 

 

2 CVBS Video-inputs for after-market Video sources (e.g. DVD-Player, DVB-T Tuner) 

 

Automatic switching to rear-view camera input on engagement of the reverse gear 

 

Activatable parking guide lines for rear-view camera (not available for all vehicles) 

 

Video-in-motion (ONLY for connected video-sources) 

 

AV-inputs NTSC compatible 

 

Summary of Contents for RL3-MIB-4




















Reviews: