background image

 

      7044-225I 

   

August 

13, 

2018

3100-I ACC WOOD INSERT

AUTOMATIC COMBUSTION CONTROL 

(ACC)

MODEL(S):

31I-ACC

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

Installation and service of this appliance should be performed by 

qualified personnel. Hearth & Home Technologies recommends 

HHT Factory Trained or NFI certified professionals.

If the information in these instructions is not 

followed exactly, a fire could result causing 

property damage, personal injury, or death.

 

 WARNING

• 

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

• 

Do not over fire - If appliance or chimney connector 

glows, you are over firing. Over firing will void your 

warranty.

• 

Comply with all minimum clearances to combustibles 

as specified.  Failure to comply may cause house 

fire.

NOTE

To obtain a French translation of this manual, please contact 

your dealer or visit 

www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous 

plaît contacter votre revendeur ou visitez 

www.quadrafire.com

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may over fire and generate 

poisonous gases (i.e. carbon monoxide).

HOT SURFACES!

 

Glass and other surfaces are hot during 

operation AND cool down.  

WARNING

Hot glass and appliance will cause burns.

•  Do not touch glass until it is cooled

•  Use leather gloves when reloading fuel

•  NEVER allow children to touch glass

•  Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

appliance.

•  Alert children and adults to hazards of high 

temperatures

• 

High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other 

flammable materials away.

Summary of Contents for 3100-I





























Reviews: