Pella INSYNCTIVE DESIGNER Series Product Manual Download

Page: 1 / 15

PELLA

DESIGNER SERIES

BETWEEN-THE-GLASS BLINDS AND SHADES WITH INSYNCTIVE

TECHNOLOGY

WHAT’S NEEDED:

• PELLA INSYNCTIVE SINGLE-CHANNEL REMOTE (required — sold separately)

: Operates Pella

Insynctive BLINDS and SHADES.

• PELLA INSYNCTIVE BRIDGE (optional — sold separately)

: Wirelessly connects your Insynctive

products to a compatible home automation system.

•

PELLA INSYNCTIVE WALL CHARGER (optional — sold separately):

Charges battery in Pella

Insynctive BLINDS and SHADES when solar charge is not available. One per household is
strongly recommended.

PELLA

DESIGNER SERIES

BETWEEN-THE-GLASS BLINDS and SHADES

can be automatically raised and lowered to improve

the comfort and convenience of your home.

PELLA

INSYNCTIVE

PRODUCT GUIDE

Blinds

Shades

BLINDS AND SHADES

For a list of compatible home automation systems, visit Pella.com/Insynctive.

Summary of Contents for INSYNCTIVE DESIGNER Series
















Search results

Summary of Contents for INSYNCTIVE DESIGNER Series

Reviews:

Related manuals for INSYNCTIVE DESIGNER Series

Brands by name

Popular brands

Pella INSYNCTIVE DESIGNER Series, Product Manual

Search results

Summary of Contents for INSYNCTIVE DESIGNER Series

Reviews:

Related manuals for INSYNCTIVE DESIGNER Series

Brands by name

Popular brands