Pavilion GHQ-C3201WX-FF PB US Installation Manual Download

Page: 1 / 84

FOR USE IN RESIDENTIAL OR MANUFACTURED HOME APPLICATIONS.

Installation must conform with local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1 / NFPA

54 - latest edition and/or the Natural Gas and Propane Installation Code CSA B149.1 - latest edition.

Where required by the authority having jurisdiction, the installation must conform to the Standard for Controls and Safety

Devices for Automatically Fired Boilers, ANSI/ASME CSD-1.

PB Heat reserves the right to discontinue, or change at any time, the designs and/or specifications of its products without

notice.

Contact Pavilion Customer Center at 1-855-443-8468, if you have any questions or concerns.

Requests to Installers

• In order to use the Combi Boiler safely, read

this installation manual carefully, and follow the

installation instructions.

• Failures and damage caused by erroneous work

or work not as instructed in this manual are not

covered by the Pavilion Limited Warranty.

• Check that the installation was done properly in

accordance with this Installation Manual upon

completion.

• After completing installation, either place this

Installation Manual and Owner’s Guide (the

warranty registration information included) in

a plastic pouch and attach it to the side of the

Combi Boiler (or the inside of the pipe cover

or recess box if applicable), or hand it to the

customer to retain for future reference. For the

warranty conditions and limitations, see the

Owner’s Guide.

CAUTION

If the information in these instructions is not

followed exactly, a fire or explosion may result

causing property damage, personal injury or

death.
• Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use

any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING

APMO

LOW-LEAD

Low NOx Approved by SCAQMD

14 ng/J or 20 ppm

(Natural Gas Only)

SBB819J

Rev. 12/19

CONDENSING GAS COMBI BOILER

Installation Manual

Models : PV199DV (GHQ-C3201WX-FF PB US)

PB HEAT, LLC

Summary of Contents for GHQ-C3201WX-FF PB US





















































































Search results

Summary of Contents for GHQ-C3201WX-FF PB US

Reviews:

Related manuals for GHQ-C3201WX-FF PB US

Brands by name

Popular brands

Pavilion GHQ-C3201WX-FF PB US, Installation Manual

Search results

Summary of Contents for GHQ-C3201WX-FF PB US

Reviews:

Related manuals for GHQ-C3201WX-FF PB US

Brands by name

Popular brands