Optex ELITE PRO Instruction Manual Download | Manualshive

Page: 1 / 24

background image

Preface

Installation

Troubleshooting

Specifications

5932260 2022.08

ELITE PRO

ELITE PRO2

ELITE PRO LE

Sensors for full-energy and low-energy automatic swing doors

Packaged combinations of
Swing Door Sensor Head

OA-607 T

Swing Door Sensor Controller

OC-907C T

Instruction Manual

Manufacturer’s statement

Read this operation manual carefully before use, to ensure proper operation of this product.
Failure to read this operation manual may cause improper operation and may result in serious injury or death of a person.
The meanings of the symbols are as follows.

WARNING

WARNING

Failure to follow the instructions provided with this indication and improper handling may cause injury and/or
property damage.

CAUTION

CAUTION

Failure to follow the instructions provided with this indication and improper handling may cause death or serious
injury.

NOTE

NOTE

Special attention is required to the section of this symbol.

1. Set door speeds and verify proper operation of door manufacturer’s equipment prior to applying power to the sensor system.
2. Do not install the sensor where it might be directly sprayed with rainwater.
3. Verify proper wiring prior to applying power to the sensor system to prevent damage to equipment.

4. When setting the sensor’s area pattern, make sure there is no traffic around the installation site.

5. Do not attempt to rebuild or repair sensor heads or control unit. Contact the address in this manual for replacement products.

6. Only use the sensor as specified in the supplied instructions.

7. Walk test the installation to verify operation is in compliance with all local laws, codes and standards of your country.
8. Upon completion of installation and adjustments, instruct the owner/operator on proper operation of the door and sensor system.

9. Identify any switches/breakers that will place the door out of service when unsafe or improper operation is identified.

Contents

Manufacturer’s statement .........................................................................1
Overview ...................................................................................................2
Accessories ...............................................................................................2
Part names ................................................................................................4
Installation .................................................................................................5
Wiring ......................................................................................................10
Power on .................................................................................................13

Indicator confirmation

..............................................................................13

Function settings .....................................................................................15
Detection area adjustment ......................................................................17
Automatic settings and auto area learn ...................................................18
Walk test .................................................................................................19
Inform building owner/operator of the following items .............................19
Troubleshooting.......................................................................................19
Dimensions .............................................................................................23

..........................................................................................24

1
2
3
...
»

Summary of Contents for ELITE PRO

























Reviews:

No comments

Related manuals for ELITE PRO

Brand: quadient Pages: 10

RazorCut 45 KUPJRRW45

Brand: Unimig Pages: 24

Brand: Vectaire Pages: 6

Brand: iWeld Pages: 76

Power Track Master Unit PTD Series

Brand: Norton Pages: 2

UWI 230 TP AC/DC

Brand: Unitor Pages: 25

ControlHoist CMT

Brand: Raynor Pages: 44

Brand: DEVI Pages: 2

Controll-A-Door RDO-1V4

Brand: B&D Pages: 23

BI-WELDER TIG 2040 DC-HF

Brand: Cebora Pages: 11

Brand: Vasco Pages: 32

Brand: Panasonic Pages: 176

3VL9300-3HE0 Series

Brand: Siemens Pages: 7

Brand: Siemens Pages: 7

3VM9 17-0FK2 Series

Brand: Siemens Pages: 10

Brand: Siemens Pages: 10

3VA9137-0FK Series

Brand: Siemens Pages: 14

Brand: LOTOS Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands