PLD-25/NiMH
SELF TESTING MAINTAINED EMERGENCY
ILLUMINATION SIGN
LED
Page
1 from
4
Page 4 from
4
Thank you for purchasing this product of
Olympia Electronics. A European manufacturer.
GENERAL
o
These luminaires are used indoors
(
ta 40 C
)
where emergency light is needed.
E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y
connected to mains power supply
.
In normal operation the led strip lights and the
battery is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically in
emergency mode (powered by its battery).
When the mains power supply is restored
the device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions on page 2,3,4.
Battery charging
The battery charging is completely controlled
.
Therebuy,
the
best
possible
battery
maintenance is
achieved
,
as well as the
elongation of its duration
.
When the battery has
completely charged
,
it charges with a
maintenance current.
Battery Cut-off
The luminaire enters in this operation when the
mains power supply fails
and battery has lost
its energy
.
During this operation the luminaire
enters the idle state
and battery consumption is
negligible, in order to be protected from deep
discharge.
Manual
Test
This test can be done by pressing the test
button. The light source and the emergency
circuit of the device is monitored. The manual
test can be conducted only if the main power
supply and the battery is connected. During
this test period all indication LEDs are OFF.
Automatic operational test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the main power supply and the
battery should be connected.
Automatic Autonomous Test
The Automatic autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. This test is conducted
automatically every 6 months
.
In order to be
performed, the main power supply and the
battery should be connected and fully charged
.
If the battery is not fully charged
,
the test is
postponed
until the battery is completely
charged. If during this test, the autonomy is
less than nominal then the battery fault led
turned on continuously and the battery must be
replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
stated in the list of the technical characteristics.
During emergency mode, a light source test is
also performed.
Resetting Errors
Push the Test button for more than 5 seconds,
to delete all the indicated LED errors. Then the
Operation temperature range
Relative humidity
Construction materials
External dimensions
(
LxWxH)
Typical weight
Guarantee
Mains voltage
Maximum power consumption
Recharging time
Battery protection
Indications / Control
Minimum emergency duration
Degrees of cover protection
Viewing distance
Produced in accordance with
Light source intensity (230V / emerg.)
3h
24h
Overcharging and full discharging protection
Charge LED, Lamp Fault LED, Battery Fault LED / Test button
IP 44
26m
90lm / 100lm
EN 60598-1, EN 60598-2-22
, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
, EN 1838
5 40 C
o
to
up to 95%
Fire retardant ABS
,
plexiglas
280x49x209mm
3 years (1 year for the battery)
890gr.
Battery (Ni-MH)
3.6V/1.5Ah
3.5W / 4VA
220-240V AC/50-60Hz
8
8
2γρ
ME PVC
922502500_09_001
922502500_09_001
High Quality European based Manufacturers
HANGING INSTALLATION
A-1130, A-1131, A-1132 SET
(OPTIONAL AFTER REQUEST)
Battery replacement process
NOTE:
LED= Light Emitting Diode
LABELING EXPLANATION:
X:
Self contained
1:
Maintained
(*)
A:
Including test device
G:
Internally illuminated safety sign
180:
3 hour duration
1
Power off the device
2
Dismantle the luminaire by pushing the lock/unlock hooks on each side and pull it down.
3
Remove the old battery and install the new battery’s connector to the appropriate P.C.B
connector.
4
Place upwards the luminaire until the plastic hooks are securely locked.
5
Power on the device
.
(*)
Maintained operation: The luminaire lights its illumination
source, when it is powered by the mains power supply or not
.
Non-Maintained operation: The luminaire lights its illumination
source,
only in power supply’s failure.
Α
Α-1130
Α-1131
Α-1132
Tube
Α=1
m
Α=0
.
5
m
Α=0
.
25
m
The light source contained in this luminaire shall only be replaced by the
manufacturer, or his agent, or a similar qualified person.
3
2
1
GENERAL!!
Measure the distance of the
mounting holes and after the drilling
place on these spots the mounting
plugs and fasten the base with the
mounting screws.
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
olympia electronics S.A
45 °C max. across the board
Non reversible connection between main pcb and led module
11-14V DC
780mW
0409153
PLD-25/NiMH
TECHNICAL CHARACTERISTICS (for LED MODULE SPECS. see page 4)
