background image

12x16 SunShed Garden Shed 

FJ Bevel Model with Metal Roof  

Assembly Manual

Some of the safety and usage measures you may wish to consider include: 
 
-snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it is advisable to sweep the 
snow off the roof(s).  
-if the product is elevated, any structural and building code requirements are solely the customer's  
responsibility, and should be abided by.  
-in high or gusty wind conditions it is advisable to keep the structure securely grounded.  
-have a regular maintenance plan to ensure screws, doors, windows and parts are tight.  

 
 
Customer agrees to hold Outdoor Living Today free of any liability for improper installation, 
maintenance and repair of any of our products.

Revision #2.5 

October 4, 2022

Thank you for purchasing 
an 12x16 SunShed Garden 
Shed from Outdoor Living  
Today. Please take the time 
to identify all the parts prior 
to assembly.

Safety Points and Other Considerations 
Our products are built for use based on 
proper installation and normal residential 
use, on level ground. Please follow the  
instruction manual when building your  
shed and retain the manual for future  
maintenance purposes.

In the event of a missing or broken piece, simply call the Outdoor Living Today Customer 
Support Line @ 1-888-658-1658 within 30 days of the delivery of your purchase. It is our  
commitment to you to courier replacement parts, free of charge, within 10 business days of 
this notification. Replacement parts will not be provided free of charge after the 30 day grace 
period. 

Stock Code # 

SSGS1216-FJ-Metal

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 1

Summary of Contents for SunShed SSGS1216-FJ-Metal





















































Reviews: